參數資料
型號： XRT75L02
廠商： Exar Corporation
英文描述： TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
中文描述： 雙通道E3/DS3/STS-1線路接口單元，其抖動
文件頁數： 44/50頁
文件大小： 343K
代理商： XRT75L02
xr
REV. 1.0.3
XRT75L02
TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
42
8.0
DIAGNOSTIC FEATURES:
8.1
The XRT75L02 contains an on-chip Pseudo Random Binary Sequence (PRBS) generator and detector for
diagnostic purpose. This feature is only available in Host mode. With the PRBSEN_n bit = “1”, the transmitter
will send out PRBS of 2
23
-1 in E3 rate or 2
15
-1 in STS-1/DS3 rate. At the same time, the receiver PRBS
detector is also enabled. When the correct PRBS pattern is detected by the receiver, the RNEG/LCV pin will go
“Low” to indicate PRBS synchronization has been achieved. When the PRBS detector is not in sync the
PRBSLS bit will be set to “1” and RNEG/LCV pin will go “High”.
With the PRBS mode enabled, the user can also insert a single bit error by toggling “INSPRBS” bit. This is
done by writing a “1” to INSPRBS bit. The receiver at RNEG/LCV pin will pulse “High” for one RxClk cycle for
every bit error detected. Any subsequent single bit error insertion must be done by first writing a “0” to
INSPRBS bit and followed by a “1”.
Figure 25 shows the status of RNEG/LCV pin when the XRT75L02 is configured in PRBS mode.
PRBS Generator and Detector:
N
OTE
:
In PRBS mode, the device is forced to operate in Single-Rail Mode.
8.2
The XRT75L02 offers three loop back modes for diagnostic purposes. In Hardware mode, the loop back
modes are selected via the RLB_n and LLB_n pins. In Host mode, the RLB_n and LLB_n bits n the Channel
control registers select the loop back modes.
8.2.1
ANALOG LOOPBACK:
In this mode, the transmitter outputs (TTIP_n and TRING_n) are connected internally to the receiver inputs
(RTIP_n and RRING_n) as shown in Figure 26. Data and clock are output at RCLK_n, RPOS_n and RNEG_n
pins for the corresponding transceiver. Analog loop back exercises most of the functional blocks of the device
including the jitter attenuator which can be selected in either the transmit or receive path.
XRT75L02 can be configured in Analog Loopback either in Hardware mode via the LLB_n and RLB_n pins or
in Host mode via LLB_n and RLB_n bits in the channel control registers.
LOOPBACKS:
N
OTES
:
1.
2.
In the Analog loopback mode, data is also output via TTIP_n and TRING_n pins.
Signals on the RTIP_n and RRING_n pins are ignored during analog loop back.
F
IGURE
25. PRBS MODE
RClk
RNEG/LCV
SYNC LOSS
PRBS SYNC
Single Bit Error
相關PDF資料
PDF描述
XRT75L02IV TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04D FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04DIV FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04 FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
相關代理商/技術參數
參數描述
XRT75L02DES 功能描述:時鐘合成器/抖動清除器 2CH T3/E3/STS1 LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02DIV-F 功能描述:網絡控制器與處理器 IC 2-Ch E3/DS3/STS-1 RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT75L02DIVTR-F 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02ES 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L02IV 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*