- 您現在的位置：買賣IC網 > PDF目錄376464 > XRT91L30IQ (EXAR CORP) STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER PDF資料下載
參數資料
| 型號： | XRT91L30IQ |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| 中文描述： | TRANSCEIVER, PQFP64 |
| 封裝： | 10 X 10 MM, 2 MM HEIGHT, PLASTIC, QFP-64 |
| 文件頁數： | 30/39頁 |
| 文件大?。?/td> | 440K |
| 代理商： | XRT91L30IQ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
XRT91L30
STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER
xr
REV. 1.0.1
28
4.0
DIAGNOSTIC FEATURES
4.1
The serial remote loopback function is activated by setting RLOOPS "High". When serial remote loopback is
activated, the high-speed serial receive data from RXIP/N is presented at the high speed transmit output
TXOP/N, and the high-speed recovered clock is selected and presented to the high-speed transmit clock input
of the Retimer. During serial remote loopback, the high-speed receive data (RXIP/N) is also converted to
parallel data and presented at the low-speed receive parallel interface RXDO[7:0]. The recovered receive clock
is also divided by 8 and presented at the low-speed clock output RXPCLKO to synchronize the transfer of the
8-bit received parallel data. A simplified block diagram of serial remote loopback is shown in Figure 18.
Serial Remote Loopback
4.2
The digital local loopback is activated when the DLOOP signal is set "High." When digital local loopback is
activated, the high-speed data from the output of the parallel to serial converter is looped back and presented
to the high-speed input of the receiver serial to parallel converter. The CMU output is also looped back to the
receive section and is used to synchronize the transfer of the data through the receiver. In Digital loopback
mode, the transmit data from the transmit parallel interface TXDI[7:0] is serialized and presented to the high-
speed transmit output TXOP/N using the high-speed 622.08/155.52 MHz transmit clock generated from the
clock multiplier unit and presented to the input of the Retimer and SIPO. A simplified block diagram of digital
loopback is shown in Figure 19. Receive Data mute upon LOS, as shown in Figure 7, applies to Digital Local
Loopback Mode.
Digital Local Loopback
F
IGURE
18. S
ERIAL
R
EMOTE
L
OOPBACK
F
IGURE
19. D
IGITAL
L
OCAL
L
OOPBACK
PISO
Re-Timer
LVPECL
Output Drivers
LVPECL
Input Drivers
CDR
SIPO
Rx Parallel Output
Tx Serial Output
Serial Remote Loopback
Rx Serial Input
PISO
Re-Timer
LVPECL
Output Drivers
LVPECL
Input Drivers
CDR
SIPO
Rx Parallel Output
Tx Serial Output
Digital Loopback
Tx Parallel Input
相關PDF資料 |
PDF描述 |
|---|---|
| XRT91L30 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L31 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L31IQ | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L32 | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
| XRT91L32IQ-F | STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT91L30IQ-F | 功能描述:網絡控制器與處理器 IC 8-Bit TTL 3.3V temp -45 to 85C;UART RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT91L30IQ-F | 制造商:Exar Corporation 功能描述:SONET Transceiver IC |
| XRT91L30IQTR | 功能描述:總線收發器 RoHS:否 制造商:Fairchild Semiconductor 邏輯類型:CMOS 邏輯系列:74VCX 每芯片的通道數量:16 輸入電平:CMOS 輸出電平:CMOS 輸出類型:3-State 高電平輸出電流:- 24 mA 低電平輸出電流:24 mA 傳播延遲時間:6.2 ns 電源電壓-最大:2.7 V, 3.6 V 電源電壓-最小:1.65 V, 2.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-48 封裝:Reel |
| XRT91L30IQTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT91L31 | 制造商:EXAR 制造商全稱:EXAR 功能描述:STS-12/STM-4 OR STS-3/STM-1 SONET/SDH TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。