- 您現在的位置：買賣IC網 > PDF目錄48107 > YNV05T16-0 (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNV05T16-0 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-10 |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 423K |
| 代理商： | YNV05T16-0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁
OCT 12, 2006 revised to APR 12, 2007
Page 8 of 26
www.power-one.com
YNV05T16 DC-DC Converter Data Sheet
3.0-5.5 VDC Input; 0.7525-3.63 VDC Programmable @ 16 A
Characterization
General Information
The converter has been characterized for many
operational aspects, to include thermal derating
(maximum load current as a function of ambient
temperature and airflow) for vertical mounting,
efficiency, start-up parameters, output ripple and
noise, and transient response to load step-change.
The figures are numbered as Fig. x.y, where x
indicates the different output voltages, and y
associates with specific plots (y = 1 for the vertical
thermal derating, …). For example, Fig. x.1 will
refer to the vertical thermal derating for all the
output voltages in general.
The following pages contain specific plots or
waveforms
associated
with
the
converter.
Additional comments for specific data are provided
below.
Test Conditions
All thermal and efficiency data presented were
taken with the converter soldered to a test board,
specifically a 0.060” thick printed wiring board
(PWB) with four layers. The top and bottom layers
were not metalized. The two inner layers,
comprising two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that
heat transfer from the converter to the PWB was
minimized. This provides a worst-case but
consistent scenario for thermal derating purposes.
All measurements requiring airflow were made in
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining
high reliability. If one anticipates operating the
converter at or close to the maximum loads
specified in the derating curves, it is prudent to
check actual operating temperatures in the
application. Thermographic imaging is preferable;
if
this
capability
is
not
available,
then
thermocouples
may
be
used.
Power-One
recommends the use of AWG #40 gauge
thermocouples to ensure measurement accuracy.
Careful routing of the thermocouple leads will
further minimize measurement error. Refer to Fig.
F for optimum measuring thermocouple location.
Fig. F: Location of the thermocouple for thermal testing.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Fig. x.1 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15 m/s to 2.5 m/s), and
vertical converter mounting. The airflow during the
testing is parallel to the long axis of the converter,
going from ON/OFF pin to output pins.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which any MOSFET
temperature does not exceed a maximum
specified temperature (120 °C) as indicated by the
thermographic image, or
(ii) The maximum current rating of the converter
(16 A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on
the PCB at the thermocouple location shown in
Fig. F should not exceed 120 °C in order to
operate inside the derating curves.
Efficiency
Fig. x.2 show the efficiency vs. load current plot for
ambient temperature of 25 C, airflow rate of 200
LFM (1 m/s) and input voltages of 4.5 V, 5.0 V,
and 5.5 V.
Fig. x.3 show the efficiency vs. load current plot for
ambient temperature of 25 C, airflow rate of 200
LFM (1 m/s) and input voltages of 3.0 V, 3.3 V,
and 3.6 V for output voltages
≤ 2.5V.
相關PDF資料 |
PDF描述 |
|---|---|
| YNV12T05-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T05-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T05G | DC-DC REG PWR SUPPLY MODULE |
| YNV12T05 | DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNV05T16-0G | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV05T16-D | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV05T16-DG | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 0.7525V TO 3.63V 16A 53W 10SIP - Bulk |
| YNV12T05 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T05G | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 0.7525V to 5.5V 5A 27.5W 5-Pin SIP |
發布緊急采購，3分鐘左右您將得到回復。