- 您現在的位置：買賣IC網 > PDF目錄48107 > YNV12T05-0 (POWER-ONE INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | YNV12T05-0 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | SIP-5 |
| 文件頁數： | 26/27頁 |
| 文件大?。?/td> | 393K |
| 代理商： | YNV12T05-0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁
Data Sheet
9.6 - 14Vdc Input; 5A, 0.7525 - 5.5Vdc Programmable Output
Rev 1 07-01-04
WWW.POWER-ONE.COM
Page 8 of 27
di/dt
Nex
TM
-v Series: YNV12T05
operating
temperatures
in
the
application.
Thermographic
imaging
is
preferable;
if
this
capability is not available, then thermocouples
may be used. di/dt recommends the use of AWG
#40 gauge thermocouples to ensure measurement
accuracy. Careful routing of the thermocouple
leads will further minimize measurement error.
Refer
to
Fig.
D
for
optimum
measuring
thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 to x.2 for maximum
temperature of 120°C. Ambient temperature was
varied between 25°C and 85°C, with airflow rates
from 30 to 500 LFM (0.15m/s to 2.5m/s), and
vertical and horizontal module mounting. The
airflow during the testing is parallel to the long axis
of the module, going from input pins to output pins.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which any MOSFET
temperature
does
not
exceed
a
maximum
specified temperature (120°C) as indicated by the
thermographic image, or
(ii) The maximum current rating of the module (5A)
During normal operation, derating curves with
maximum FET temperature less than or equal to
120°C should not be exceeded. Temperature on
the PCB at the thermocouple location shown in
Fig. D should not exceed 120°C in order to
operate inside the derating curves.
Fig. D: Location of the thermocouple for thermal testing.
Efficiency
Figure x.3 shows the efficiency vs. load current
plot for ambient temperature of 25C, airflow rate
of 200 LFM (1 m/s) and input voltages of 9.6V,
12V and 14V.
Power Dissipation
Fig. x.4 shows the power dissipation vs. load
current plot for Ta = 25C, airflow rate of 200 LFM
(1 m/s) with vertical mounting and input voltages
of 9.6V, 12V and 14V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1
F ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test
setup shown in Fig. E.
i
S
Vout
Vsource
1
F
ceramic
capacitor
1
H
source
inductance
DC/DC
Converter
4 x 47
F
ceramic
capacitor
47
F
ceramic
capacitor
C
O
C
IN
Nex -v Series
TM
Vin
GND
Vout
Fig. E: Test Set-up for measuring input reflected ripple
currents,
i
s and output voltage ripple.
相關PDF資料 |
PDF描述 |
|---|---|
| YNV12T05G | DC-DC REG PWR SUPPLY MODULE |
| YNV12T05 | DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YNV12T10-0-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| YNV12T05G | 制造商:Power-One 功能描述:Module DC-DC 1-OUT 0.7525V to 5.5V 5A 27.5W 5-Pin SIP |
| YNV12T05-G | 功能描述:DC/DC轉換器 0.7525-5.5Vout 5A 9.6-14VIn RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T05-G-Q | 制造商:Power-One 功能描述:DC/DC CONVERTER 0.7525-5.5V 28W |
| YNV12T10-0 | 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| YNV12T10010-0 | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 1V 10A 50W 10SIP - Bulk |
發布緊急采購，3分鐘左右您將得到回復。