參數資料
型號： Z53C8003VSC
廠商： ZILOG INC
元件分類： 總線控制器
英文描述： SMALL COMPUTER SYSTEM INTERFACE (SCSI)
中文描述： SCSI BUS CONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 12/40頁
文件大?。?/td> 447K
代理商： Z53C8003VSC
12
Z53C80 SCSI
PS97SCC0200
Z
ILOG
FUNCTIONAL DESCRIPTION
(Continued)
Bus and Status Register.
Address 5(Read Only). The
Bus and Status Register (Figure 14) is a read-only register
which can be used to monitor the remaining SCSI control
signals not found in the Current SCSI Bus Status Registers
(/ATN and /ACK), as well as six other status bits. The
following describes each bit of the Bus Status Register
individually.
Bit 0.
/ACK.Bit 0 reflects the condition of the SCSI Bus
control signal /ACK. This signal is normally monitored by
the Target device.
Bit 1.
/ATN.Bit 1 reflects the condition of the SCSI Bus
control signal /ATN. This signal is normally monitored by
the Target device.
Bit 4.
Interrupt Request Active.Bit 4 is set if an enabled
interrupt condition occurs. It reflects the current state of the
IRQ output and can be cleared by reading the Reset Parity/
Interrupt Register.
Bit 5.
Parity Error.Bit 5 is set if a parity error occurs during
a data receive or a device selection. The Parity Error bit can
only be set (1) if the Enable Parity Check bit (Mode
Register, bit 5) is active (1). This bit may be cleared by
reading the Reset Parity/Interrupt Register.
Bit 6.
DMA Request.The DMA Request bit allows the CPU
to sample the output pin DRQ. DRQ can be cleared by
asserting /DACK or by resetting the DMA MODE bit (bit 1)
in the Mode Register. The DRQ signal does not reset when
a phase-mismatch interrupt occurs.
Bit 7.
End Of DMA Transfer.The End Of DMA Transfer bit
is set if /EOP, /DACK, and either /RD or /WR are
simultaneously active for at least 100 ns. Since the /EOP
signal can occur during the last byte sent to the Output
Data Register, the /REQ and /ACK signals should be
monitored to ensure that the last byte has been transferred.
This bit is reset when the DMA MODE bit is reset (0) in the
Mode Register.
DMA Registers.
Three write-only registers are used to
initiate all DMA activity. They are: Start DMA Send, Start
DMA Target Receive, and Start DMA Initiator Receive.
Performing a write operation into one of these registers
starts the desired type of DM transfer. Data presented to
the SCSI on signals D7-D0 during the register write is
meaningless and has no effect on the operation. Prior to
writing these registers, the DMA Mode bit (bit 1), and the
Target mode bit (bit 6) in the Mode Register must be
appropriately set. The individual registers are briefly
described as follows:
Start DMA Send.
Address 5(Write Only). This register is
written to initiate a DMA send, from the DMA to the SCSI
Bus, for either Initiator or Target role operations. The DMA
Mode bit (Mode Register, bit 1) is set prior to writing this
register.
Start DMA Target Receive.
Address 6(Write Only). This
register is written to initiate a DMA receive - from the SCSI
Bus to the DMA, for Target operation only. The DMA Mode
bit (bit 1) and the Targetmode bit (bit 6) in the Mode
Register must both be set (1) prior to writing this register.
/ACK
/ATN
Busy Error
Phase Match
Interrupt Request Active
Parity Error
DMA Request
End of DMA
Address: 5
(Read Only)
D7 D6 D5 D4 D3 D2 D1 D0
Figure 14. Bus and Status Register
Bit 2.
Busy Error.The Busy Error bit is active if an unexpected
loss of the /BSY signal has occurred. This latch is set
whenever the Monitor Busy bit (Mode Register, bit 2) is
True and /BSY is False. An unexpected loss of /BSY
disables any SCSI outputs and resets the DMA Mode bit
(Mode Register, bit 1).
Bit 3.
Phase Match.The SCSI signals /MSG, C//D, and
I//O, represent the current information transfer phase. The
Phase Match bit indicates whether the current SCSI Bus
phase matches the lower three bits of the Target Command
Register. Phase Match is continuously updated and is only
significant when operating as a Bus Initiator. A phase
match is required for data transfers to occur on the SCSI
Bus.
相關PDF資料
PDF描述
Z53C80SCSI SMALL COMPUTER SYSTEM INTERFACE (SCSI)
Z54122 RETRIGGERABLE MONOSTABLE MULTIVIBRATOR
Z5U0603 ceramic chip capacitors
Z5U0805 ceramic chip capacitors
Z5U1206 ceramic chip capacitors
相關代理商/技術參數
參數描述
Z53C8003VSC00TR 功能描述:IC Z53C80 SCSI 44PLCC RoHS:否 類別:集成電路 (IC) >> 接口 - 信號終端器 系列:Z53C80 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:SCSI，SE 端子數:9 電源電壓:4 V ~ 5.25 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件
Z53C8003VSG 功能描述:SCSI 接口集成電路 3MB/SEC CMOS SCSI I RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube
Z53C80-10PSC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC
Z53C80SCSI 制造商:ZILOG 制造商全稱:ZILOG 功能描述:SMALL COMPUTER SYSTEM INTERFACE (SCSI)
Z53E11 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:E5M Operation Manual DX CODE ZA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*