參數資料
型號： Z86C36
廠商： ZiLOG, Inc.
英文描述： CMOS Z8 MCU(CMOS Z8系列微控制器)
中文描述： 單片機的CMOS Z8的CMOS（Z8系列微控制器）
文件頁數： 37/70頁
文件大?。?/td> 1192K
代理商： Z86C36
Z86C34/C35/C36/C44/C45/C46
CMOS Z8 MCUs with ASCI UART
ZiLOG
DS007601-Z8X0499
P R E L I M I N A R Y
37
Power-On-Reset (POR).
A timer circuit clocked by a ded-
icated on-board RC oscillator is used for the Power-On Re-
set (
POR
) timer function. The
POR
time allows
V
CC
and the
oscillator circuit to stabilize before instruction execution
begins.
The
POR
timer circuit is a one-shot timer triggered by one
of three conditions:
1. Power fail to Power OK status.
2. Stop-Mode Recovery (if
D5
of
SMR = 1
).
3.
WDT
time-out.
The
POR
time is specified as
T
POR
. Bit
5
of the Stop-Mode
Register determines whether the
POR
timer is bypassed af-
ter Stop-Mode Recovery (typical for external clock,
RC
/
LC
oscillators).
HALT.
HALT
turns off the internal CPU clock, but not the
XTAL
oscillation. The counter/timers and external inter-
rupts
IRQ0
,
IRQ1
,
IRQ2
, and
IRQ3
remain active. The de-
vices are recovered by interrupts and are either externally
or internally generated. An interrupt request must be en-
abled and executed to exit
HALT
mode. After the interrupt
service routine, the program continues from the instruction
after the
HALT
.
In order to enter
STOP
(or
HALT
) mode, it is necessary to
first flush the instruction pipeline to avoid suspending ex-
ecution in mid-instruction. Therefore, the user must execute
a
NOP
(Op Code =
FFH
) immediately before the appropriate
sleep instruction. For example:
STOP.
This instruction turns off the internal clock and ex-
ternal crystal oscillation. It also reduces the standby current
to 10 μA or less. The
STOP
mode is terminated by a
RESET
only, either by
WDT
time-out,
POR
,
SMR
recovery, or ex-
ternal reset. As a result, the processor restarts the applica-
tion program at address
000Ch
. A
WDT
time-out in
STOP
mode affects all registers the same as if a Stop-Mode Re-
covery occurred via a selected Stop-Mode Recovery source
except that the
POR
delay is enabled even if the delay is se-
lected for disable.
Note:
If a permanent
WDT
is selected, the
WDT
runs in all
modes and cannot be stopped or disabled if the onboard
RC
oscillator is selected to drive the
WDT
.
Port Configuration Register (PCON).
The
PCON
regis-
ter configures the ports individually; comparator output on
Port 3, open-drain on Port 0 and Port 1, low EMI on Ports
Figure 24. Oscillator Configuration
XTAL1
XTAL2
C1
C2
C1
C2
C1
XTAL1
XTAL2
XTAL1
XTAL2
XTAL1
XTAL2
Ceramic Resonator or
Crystal
C1, C2 = 47 pF TYP *
f = 8 MHz
LC
C1, C2 = 22 pF
L = 130 uH *
f = 3 MHz *
RC
@ 5V V (TYP)
C1 = 33 pF *
R = 1K *
f = 6 MHz *
External Clock
L
R
*Preliminary value including pin parasitics
**Device ground pin
V **
V **
V **
V **
V **
FF
6F
NOP
STOP
; clear the pipeline
; enter STOP mode
or
; clear the pipeline
; enter HALT Mode
FF
7F
NOP
HALT
相關PDF資料
PDF描述
Z86C44 CMOS Z8 MCU(CMOS Z8系列微控制器)
Z86C45 CMOS Z8 MCU(CMOS Z8系列微控制器)
Z86C46 CMOS Z8 MCU(CMOS Z8系列微控制器)
Z86C40 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C30 CMOS Z8 CONSUMER CONTROLLER PROCESSOR
相關代理商/技術參數
參數描述
Z86C3600ZEM 功能描述:仿真器/模擬器 Z8 C36 ICEBOX RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
Z86C40 制造商:ZILOG 制造商全稱:ZILOG 功能描述:CMOS Z8 CONSUMER CONTROLLER PROCESSOR
Z86C4000ZDV 功能描述:仿真器/模擬器 Z86C40 PLCC Em Pod RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
Z86C4001ZDV 功能描述:仿真器/模擬器 Z86C40 PLCC Em Pod RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
Z86C4016FEC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*