- 您現在的位置：買賣IC網 > PDF目錄373785 > ZL50019 (Zarlink Semiconductor Inc.) Enhanced 2 K Digital Switch with Stratum 4E DPLL PDF資料下載
參數資料
| 型號： | ZL50019 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Enhanced 2 K Digital Switch with Stratum 4E DPLL |
| 中文描述： | 2度增強數字交換與地層4E條數字鎖相環 |
| 文件頁數： | 21/115頁 |
| 文件大?。?/td> | 866K |
| 代理商： | ZL50019 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
ZL50019
Data Sheet
21
Zarlink Semiconductor Inc.
unused ST-BUS/GCI-Bus channel (high impedance) are driven high. Refer to Figure 18 on page 32 for a
diagrammatical explanation.
5.2 Input Clock (CKi) and Input Frame Pulse (FPi) Timing
The input clock for the ZL50019 can be arranged in one of three different ways. These different ways will be
explained further in Section 12.1 to Section 12.3 on page 37. Depending on the mode of operation, the input clock,
CKi, will be based on the highest data rate of either the input or both the input and output data rates. The user has
to program the CKIN1 - 0 (bits 6 - 5) in the Control Register (CR) to indicate the width of the input frame pulse and
the frequency of the input clock supplied to the device.
In Master mode and Divided Slave mode, the input clock, CKi, must be at least twice the highest input or output
data rate. For example, if the highest input data rate is 4.096 Mbps and the highest output data rate is 8.192 Mbps,
the input clock, CKi, must be 16.384 MHz, which is twice the highest overall data rate. The only exception to this is
for 16.384 Mbps input or output data. In this case, the input clock, CKi, is equal to the data rate. The input frame
pulse, FPi, must always follow CKi.
In Master mode, CKo2 and FPo2 can be programmed to be used as CKi and FPi by setting CKi_LP (bit 10) in the
Control Register (CR). This will internally loop back the CKo2 and FPo2 timing. When this bit is set, CKi and FPi
must be tied low or high externally.
In Multiplied Slave mode, the input clock, CKi, must be at least twice the highest input data rate, regardless of the
output data rate. Following the example above, if the highest input data rate is 4.096 Mbps, the input clock, CKi,
must be 8.192 MHz, regardless of the output data rate. The only exception to this is for 16.384 Mbps input data. In
this case, the input clock, CKi, is equal to the data rate. The input frame pulse, FPi, must always follow CKi.
The ZL50019 accepts positive and negative ST-BUS/GCI-Bus input clock and input frame pulse formats via the
programming of CKINP (bit 8) and FPINP (bit 7) in the Control Register (CR). By default, the device accepts the
negative input clock format and ST-BUS format frame pulses. However, the switch can also accept a positive-going
clock format by programming CKINP (bit 8) in the Control Register (CR). A GCI-Bus format frame pulse can be
used by programming FPINPOS (bit 9) and FPINP (bit 7) in the Control Register (CR).
Highest
Input or Output
Data Rate
CKIN 1-0 Bits
Input Clock Rate (CKi)
Input Frame Pulse (FPi)
16.384 Mbps or 8.192 Mbps
00
16.384 MHz
8 kHz (61 ns wide pulse)
4.096 Mbps
01
8.192 MHz
8 kHz (122 ns wide pulse)
2.048 Mbps
10
4.096 MHz
8 kHz (244 ns wide pulse)
Table 1 - CKi and FPi Configurations for Master and Divided Slave Modes
Highest
Input
Data Rate
CKIN 1-0 Bits
Input Clock Rate (CKi)
Input Frame Pulse (FPi)
16.384 Mbps or 8.192 Mbps
00
16.384 MHz
8 kHz (61 ns wide pulse)
4.096 Mbps
01
8.192 MHz
8 kHz (122 ns wide pulse)
2.048 Mbps
10
4.096 MHz
8 kHz (244 ns wide pulse)
Table 2 - CKi and FPi Configurations for Multiplied Slave Mode
相關PDF資料 |
PDF描述 |
|---|---|
| ZL50019GAC | Enhanced 2 K Digital Switch with Stratum 4E DPLL |
| ZL50019QCC | Enhanced 2 K Digital Switch with Stratum 4E DPLL |
| ZL50022 | Enhanced 4 K Digital Switch with Stratum 4E DPLL |
| ZL50022GAC | Enhanced 4 K Digital Switch with Stratum 4E DPLL |
| ZL50022QCC | Enhanced 4 K Digital Switch with Stratum 4E DPLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZL50019_06 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Enhanced 2 K Digital Switch with Stratum 4E DPLL |
| ZL50019GAC | 制造商:Microsemi Corporation 功能描述:2K WITH RATE CONVERSION AND S4 - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 2K-CH ENH 256PBGA 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 2K-CH ENH 256PBGA |
| ZL50019GAG2 | 制造商:Microsemi Corporation 功能描述:PB FREE 2K WITH RATE CONVERSION+S4E DPLL 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K 1.8V/3.3V 256BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 2K-CH ENH 256PBGA 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 2K-CH ENH 256PBGA |
| ZL50019QCC | 制造商:Microsemi Corporation 功能描述:2K WITH RATE CONVERSION AND S4 - Trays |
| ZL50019QCG1 | 制造商:Microsemi Corporation 功能描述:PB FREE 2K WITH+CONVERSION AND S4E DPLL - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TDM SWITCH 2K-CH ENH 256LQFP 制造商:Microsemi Corporation 功能描述:IC TDM SWITCH 2K-CH ENH 256LQFP |
發布緊急采購，3分鐘左右您將得到回復。