- 您現在的位置：買賣IC網 > PDF目錄382783 > μPD23C64000AL (NEC Corp.) 64M-Bit Mask-Programmble ROM(64M位掩膜可編程ROM) PDF資料下載
參數資料
| 型號： | μPD23C64000AL |
| 廠商： | NEC Corp. |
| 英文描述： | 64M-Bit Mask-Programmble ROM(64M位掩膜可編程ROM) |
| 中文描述： | 6400位掩模可編程光盤（6400位掩膜可編程光盤） |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 111K |
| 代理商： | ΜPD23C64000AL |
15
μ
PD23C64000AL
Preliminary Data Sheet
1
PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note: Strong electric field, when exposed to a MOS device, can cause destruction
of the gate oxide and ultimately degrade the device operation. Steps must
be taken to stop generation of static electricity as much as possible, and
quickly dissipate it once, when it has occurred. Environmental control
must be adequate. When it is dry, humidifier should be used. It is
recommended to avoid using insulators that easily build static electricity.
Semiconductor devices must be stored and transported in an anti-static
container, static shielding bag or conductive material. All test and
measurement tools including work bench and floor should be grounded.
The operator should be grounded using wrist strap. Semiconductor devices
must not be touched with bare hands. Similar precautions need to be taken
for PW boards with semiconductor devices on it.
2
HANDLING OF UNUSED INPUT PINS FOR CMOS
Note: No connection for CMOS device inputs can be cause of malfunction. If no
connection is provided to the input pins, it is possible that an internal input
level may be generated due to noise, etc., hence causing malfunction. CMOS
devices behave differently than Bipolar or NMOS devices. Input levels of
CMOS devices must be fixed high or low by using a pull-up or pull-down
circuitry. Each unused pin should be connected to V
DD
or GND with a
resistor, if it is considered to have a possibility of being an output pin. All
handling related to the unused pins must be judged device by device and
related specifications governing the devices.
3
STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Power-on does not necessarily define initial status of MOS device. Produc-
tion process of MOS does not define the initial operation status of the device.
Immediately after the power source is turned ON, the devices with reset
function have not yet been initialized. Hence, power-on does not guarantee
out-pin levels, I/O settings or contents of registers. Device is not initialized
until the reset signal is received. Reset operation must be executed imme-
diately after power-on for devices having reset function.
NOTES FOR CMOS DEVICES
相關PDF資料 |
PDF描述 |
|---|---|
| μPD23C64000L | 64M-Bit Mask-Programmble ROM(64M位掩膜可編程ROM) |
| μPD29F008AL-X | 8 M-Bit CMOS Low Voltage Flash Memory(8M CMOS低壓閃存) |
| μPD29F008L | 8 M-Bit CMOS 3.0 V-Only Flash Memory(8M CMOS 3V工作電壓的閃存) |
| μPD30100 | 64-bit RISC Microprosessor(64位 RISC 微處理器) |
| μPD30101 | 64-Bit Microprocessor(64位微處理器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PD23T2 | 制造商:RFHIC 制造商全稱:RFHIC 功能描述:2Way Power Divider |
| PD24 | 功能描述:烙鐵 Solder Pot 250W/1100 RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| PD240 | 制造商:MARTINDALE ELECTRIC 功能描述:PROVING DEVICE 240VOLT |
| PD2401 | 功能描述:三極與 SCR 輸出光電耦合器 500 BLOCKING VOLT 1.0 AMPS RoHS:否 制造商:Vishay Semiconductors 輸出設備:PhotoTriac 每芯片的通道數量: 絕緣電壓:3750 Vrms 正向電流:10 mA 正向電壓:1.2 V 最大觸發電流:10 mA 關斷狀態下輸出電壓-VDRM:600 V 最大連續輸出電流: 零交叉電路: 封裝:Reel |
| PD2401_10 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:AC Solid State Relays |
發布緊急采購，3分鐘左右您將得到回復。