- 您現在的位置：買賣IC網 > PDF目錄3908 > 101-0411 (Rabbit Semiconductor)INTERFACE 12KEYDISP ETHNT OP6700 PDF資料下載
參數資料
| 型號： | 101-0411 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 10/90頁 |
| 文件大?。?/td> | 0K |
| 描述： | INTERFACE 12KEYDISP ETHNT OP6700 |
| 標準包裝： | 25 |
| 系列： | SBC |
| 模塊/板類型： | 單板計算機模塊 |
| 適用于相關產品： | OP6700 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁
14
Intellicom (OP6600/OP6700)
2.5 Starting Dynamic C
Once the Intellicom is connected to your PC and to a power source, start Dynamic C by double-
clicking on the Dynamic C
icon on your desktop or in your Start menu.
If you are using a USB port to connect your computer to the Intellicom, choose Options >
Project Options
and select “Use USB to Serial Converter.” Click OK.
Dynamic C defaults to using the serial port on your PC that you specified during installa-
tion. If the port setting is correct, Dynamic C should detect the Intellicom and go through
a sequence of steps to cold-boot the Intellicom and to compile the BIOS. (Some versions
of Dynamic C will not do the initial BIOS compile and load until the first time you com-
pile a program.)
If you receive the message No Rabbit Processor Detected, the programming
cable may be connected to the wrong COM port, a connection may be faulty, or the target
system may not be powered up. First, check both ends of the programming cable to ensure
that it is firmly plugged into the PC and the programming port with the marked (colored)
edge of the programming cable towards pin 1 of the programming header.
If there are no faults with the hardware, select a different COM port within Dynamic C.
From the Options menu, select Communications. Select another COM port from the list,
then click OK. Press <Ctrl-Y> to force Dynamic C to recompile the BIOS. If Dynamic C
still reports it is unable to locate the target system, repeat the above steps until you locate the
active COM port. You should receive a Bios compiled successfully message
once this step is completed successfully.
If Dynamic C appears to compile the BIOS successfully, but you then receive a communi-
cation error message when you compile and load a sample program, it is possible that your
PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
Locate the Serial Options dialog in the Dynamic C Options > Communications
menu. Select a slower Max download baud rate.
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
Locate the Serial Options dialog in the Dynamic C Options > Communications
menu. Choose a lower debug baud rate.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
| 25FMN-BMT-A-TF | CONN FMN HSNG 25POS SNGL NOR SMD |
| 046239012001800+ | CONN FPC ONE-TOUCH LCK .5MM 12 |
| AT24C01-10PI-1.8 | IC EEPROM 1KBIT 400KHZ 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10104110 | 制造商:FCI-CONNECTOR 制造商全稱:FCI connector 功能描述:MICRO USB B TYPE RECEPTACLE |
| 10104110-0001LF | 功能描述:USB接頭 5P Quick Connect Micro USB TypeB Rcpt RoHS:否 制造商:FCI 產品:USB Type A Connectors 標準:USB 3.0 端口數量: 位置/觸點數量:9 型式:Female 電流額定值:1.8 A 安裝風格:Through Hole 端接類型:Solder Pin 連接器類型:USB 3.0 Receptacle |
| 10104110-0001LF | 制造商:FCI 功能描述:MICRO USB B, RECEPTACLE, 5POS, SMT RT AN |
| 10-104-11-01 | 制造商:Concord Electronics Inc 功能描述:Contact Solder ST Thru-Hole |
| 10-104-11-03 | 制造商:Concord Electronics Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。