參數資料
型號: 20-101-0383
廠商: Rabbit Semiconductor
文件頁數: 26/80頁
文件大?。?/td> 0K
描述: MODULE RABBITCORE RCM2020
標準包裝: 1
系列: RabbitCore®
模塊/板類型: MPU 核心模塊
適用于相關產品: RCM2020
產品目錄頁面: 620 (CN2011-ZH PDF)
其它名稱: 316-1082
28
RabbitCore RCM2000
4.2 Memory I/O Interface
Thirteen of the Rabbit 2000 address lines (A0–A12) and all the data lines (D0–D7) are
available as outputs on the RCM2000. I/0 write (/IOWR), I/0 read (/IORD), buffer enable
(/BUFEN), and Watchdog Output (/WDO) are also available for interfacing to external
devices.
The STATUS output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output.
4.2.1 Additional I/0
Although, the output clock is available on the PCLK pin, the output clock is disabled in
software starting with Dynamic C v 7.02 and later. This reduces radiated emissions. The
primary function of PCLK is as a peripheral clock or a peripheral clock ÷ 2, but PCLK can
instead be used as a digital output. See Section 5.2.1, “PCLK Output,” for more informa-
tion.
Two status mode pins, SMODE0 and SMODE1, are available as inputs. The logic state of
these two pins determines the startup procedure after a reset. /RES_IN is an external input
used to reset the Rabbit 2000 microprocessor and RCM2000 memory. /RES_OUT is an
output from the reset circuitry that can be used to reset other peripheral devices.
4.3 Serial Communication
The RCM2000 does not have an RS-232 or an RS-485 transceiver directly on the board.
However, the Prototyping Board does support a industry standard RS-232 transceiver
chip. See Appendix B, “Prototyping Board,” for more information.
4.3.1 Serial Ports
There are four serial ports designated as Serial Ports A, B, C, and D. All four serial ports
can operate in an asynchronous mode up to the baud rate of the system clock divided by
32. An asynchronous port can handle 7 or 8 data bits. A 9th bit address scheme, where an
additional bit is sent to mark the first byte of a message, is also supported. Serial Ports A
and B can be operated alternately in the clocked serial mode. In this mode, a clock line
synchronously clocks the data in or out. Either of the two communicating devices can sup-
ply the clock. When the Rabbit provides the clock, the baud rate can be up to 1/4 of the
system clock frequency, or more than 6.45 Mbps for a 25.8 MHz clock speed.
相關PDF資料
PDF描述
AT25128N-10SI-2.7 IC EEPROM 128KBIT 3MHZ 8SOIC
345-030-523-201 CARDEDGE 30POS DUAL .100 GREEN
345-030-521-802 CARDEDGE 30POS DUAL .100 GREEN
AT25128-10PI-2.7 IC EEPROM 128KBIT 3MHZ 8DIP
345-030-521-804 CARDEDGE 30POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
20-101-0389 功能描述:子卡和OEM板 SR9200 16IN/8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0390 功能描述:子卡和OEM板 SR9210 8 in/ 16 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0391 功能描述:子卡和OEM板 SR9220 DIG I/O 8IN 8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0392 功能描述:子卡和OEM板 SR9300 A/D 0-10V RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0393 功能描述:子卡和OEM板 SR9400 D/A CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit