- 您現在的位置：買賣IC網 > PDF目錄3912 > 20-101-0383 (Rabbit Semiconductor)MODULE RABBITCORE RCM2020 PDF資料下載
參數資料
| 型號： | 20-101-0383 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 27/80頁 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2020 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2020 |
| 產品目錄頁面： | 620 (CN2011-ZH PDF) |
| 其它名稱： | 316-1082 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
User’s Manual
29
4.3.2 Programming Port
The RCM2000 has a 10-pin program header labeled J3. The programming port uses the
Rabbit 2000’s Serial Port A for communication. Dynamic C uses the programming port to
download and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Serial Programming Port
All three clocked Serial Port A signals are available as
a synchronous serial port
an asynchronous serial port, with the clock line usable as a general CMOS input
The serial programming port may also be used as a serial port via the DIAG connector on
the serial programming cable.
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the serial programming port.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000. These two
SMODE pins can be used as general inputs once the cold boot is complete.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the
onboard peripheral circuits on the RabbitCore module. The serial programming port can be
used to force a hard reset on the RabbitCore module by asserting the /RESET_IN signal.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information.
相關PDF資料 |
PDF描述 |
|---|---|
| AT25128N-10SI-2.7 | IC EEPROM 128KBIT 3MHZ 8SOIC |
| 345-030-523-201 | CARDEDGE 30POS DUAL .100 GREEN |
| 345-030-521-802 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25128-10PI-2.7 | IC EEPROM 128KBIT 3MHZ 8DIP |
| 345-030-521-804 | CARDEDGE 30POS DUAL .100 GREEN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 20-101-0389 | 功能描述:子卡和OEM板 SR9200 16IN/8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0390 | 功能描述:子卡和OEM板 SR9210 8 in/ 16 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0391 | 功能描述:子卡和OEM板 SR9220 DIG I/O 8IN 8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0392 | 功能描述:子卡和OEM板 SR9300 A/D 0-10V RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0393 | 功能描述:子卡和OEM板 SR9400 D/A CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
發布緊急采購，3分鐘左右您將得到回復。