- 您現在的位置：買賣IC網 > PDF目錄3912 > 20-101-0383 (Rabbit Semiconductor)MODULE RABBITCORE RCM2020 PDF資料下載
參數資料
| 型號： | 20-101-0383 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 59/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | MODULE RABBITCORE RCM2020 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2020 |
| 產品目錄頁面： | 620 (CN2011-ZH PDF) |
| 其它名稱： | 316-1082 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
58
RabbitCore RCM2000
B.4 Using the Prototyping Board
The Prototyping Board is actually both a demonstration board and a prototyping board. As
a demonstration board, it can be used to demonstrate the functionality of the RCM2000
right out of the box without any modifications to either board. There are no jumpers or dip
switches to configure or misconfigure on the Prototyping Board so that the initial setup is
very straightforward.
The Prototyping Board comes with the basic components necessary to demonstrate the
operation of the RCM2000. Two LEDs (DS2 and DS3) are connected to PA0 and PA1, and
two switches (S2 and S3) are connected to PB2 and PB3 to demonstrate the interface to
the Rabbit 2000 microprocessor. Reset switch S1 is the hardware reset for the RCM2000.
To maximize the availability of RCM2000 resources, the demonstration hardware (LEDs
and switches) on the Prototyping Board may be disconnected. This is done by cutting the
traces below the silk-screen outline of header JP1 on the bottom side of the Prototyping
Board. Figure B-4 shows the four places where cuts should be made. An exacto knife
would work nicely to cut the traces. Alternatively, a small standard screwdriver may be
carefully and forcefully used to wipe through the PCB traces.
Figure B-4. Where to Cut Traces to Permanently Disable
Demonstration Hardware on Prototyping Board
The power LED (PWR) and the RESET switch remain connected. Jumpers across the
appropriate pins on header JP1 can be used to reconnect specific demonstration hardware
later if needed.
S2
PB3
PB2
PA1
PA0
DS3
S3
DS2
Cut
JP1
Bottom Side
相關PDF資料 |
PDF描述 |
|---|---|
| AT25128N-10SI-2.7 | IC EEPROM 128KBIT 3MHZ 8SOIC |
| 345-030-523-201 | CARDEDGE 30POS DUAL .100 GREEN |
| 345-030-521-802 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25128-10PI-2.7 | IC EEPROM 128KBIT 3MHZ 8DIP |
| 345-030-521-804 | CARDEDGE 30POS DUAL .100 GREEN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 20-101-0389 | 功能描述:子卡和OEM板 SR9200 16IN/8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0390 | 功能描述:子卡和OEM板 SR9210 8 in/ 16 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0391 | 功能描述:子卡和OEM板 SR9220 DIG I/O 8IN 8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0392 | 功能描述:子卡和OEM板 SR9300 A/D 0-10V RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0393 | 功能描述:子卡和OEM板 SR9400 D/A CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
發布緊急采購，3分鐘左右您將得到回復。