- 您現在的位置：買賣IC網 > PDF目錄371396 > 24FC65 (Microchip Technology Inc.) 64K 5.0V 1MHz CMOS Smart Serial EEPROMs(4.5~5.5V,64K位,10M次擦寫周期,IIC智能串行EEPROM) PDF資料下載
參數資料
| 型號： | 24FC65 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K 5.0V 1MHz CMOS Smart Serial EEPROMs(4.5~5.5V,64K位,10M次擦寫周期,IIC智能串行EEPROM) |
| 中文描述： | 64K的5.0V的CMOS 1MHz的智能（4.5?5.5V的，64K的位，1000萬次擦寫周期，國際進口智能串行EEPROM的串行EEPROM） |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 237K |
| 代理商： | 24FC65 |
24FC65
DS21125C-page 4
1997 Microchip Technology Inc.
2.0
FUNCTIONAL DESCRIPTION
The 24FC65 supports a bidirectional two-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus must be controlled
by a master device which generates the serial clock
(SCL), controls the bus access, and generates the
START and STOPs, while the 24FC65 works as slave.
Both master and slave can operate as transmitter or
receiver but the master device determines which mode
is activated.
3.0
BUS CHARACTERISTICS
The following
bus protocol
has been defined:
Data transfer may be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP.
Accordingly, the following bus conditions have been
defined (Figure 3-1).
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START. All
commands must be preceded by a START.
3.3
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP. All operations
must be ended with a STOP.
3.4
Data Valid (D)
The state of the data line represents valid data when,
after a START, the data line is stable for the duration of
the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START and
terminated with a STOP. The number of the data bytes
transferred between the START and STOPs is
determined by the master device.
3.5
Acknowledge
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this acknowledge bit.
A device that acknowledges must pull down the SDA
line during the acknowledge clock pulse in such a way
that the SDA line is stable LOW during the HIGH period
of the acknowledge related clock pulse. Of course,
setup and hold times must be taken into account.
During reads, a master must signal an end of data to
the slave by NOT generating an acknowledge bit on the
last byte that has been clocked out of the slave. In this
case, the slave (24FC65) must leave the data line HIGH
to enable the master to generate the STOP.
Note:
The 24FC65 does not generate any
acknowledge bits if an internal program-
ming cycle is in progress.
FIGURE 3-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
SCL
SDA
(A)
(B)
START
Condition
(C)
(A)
(D)
(D)
Address
or
Acknowledge
Valid
Data Allowed
to Change
STOP
Condition
相關PDF資料 |
PDF描述 |
|---|---|
| 24HCA | surface mount silicon Zener diodes |
| 24HCB | surface mount silicon Zener diodes |
| 24HCC | surface mount silicon Zener diodes |
| 24HCD | surface mount silicon Zener diodes |
| 24HC | XTAL PLAS SMT 12X4 4PAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24FC65/P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24FC65-/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
| 24FC65/SM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24FC65-/SM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
| 24FC65_04 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
發布緊急采購，3分鐘左右您將得到回復。