- 您現在的位置：買賣IC網 > PDF目錄371396 > 24FC65 (Microchip Technology Inc.) 64K 5.0V 1MHz CMOS Smart Serial EEPROMs(4.5~5.5V,64K位,10M次擦寫周期,IIC智能串行EEPROM) PDF資料下載
參數資料
| 型號： | 24FC65 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K 5.0V 1MHz CMOS Smart Serial EEPROMs(4.5~5.5V,64K位,10M次擦寫周期,IIC智能串行EEPROM) |
| 中文描述： | 64K的5.0V的CMOS 1MHz的智能（4.5?5.5V的，64K的位，1000萬次擦寫周期，國際進口智能串行EEPROM的串行EEPROM） |
| 文件頁數： | 9/16頁 |
| 文件大小： | 237K |
| 代理商： | 24FC65 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
1997 Microchip Technology Inc.
DS21125C-page 9
24FC65
7.0
PAGE CACHE AND ARRAY
MAPPING
The cache is a 64 byte (8 pages x 8 bytes) FIFO buffer.
The cache allows the loading of up to 64 bytes of data
before the write cycle is actually begun, effectively
providing a 64-byte burst write at the maximum bus
rate. Whenever a write command is initiated, the cache
starts loading and will continue to load until a stop bit is
received to start the internal write cycle. The total length
of the write cycle will depend on how many pages are
loaded into the cache before the stop bit is given. Max-
imum cycle time for each page is 5 ms. Even if a page
is only partially loaded, it will still require the same cycle
time as a full page. If more than 64 bytes of data are
loaded before the stop bit is given, the address pointer
will wrap around' to the beginning of cache page 0 and
existing bytes in the cache will be overwritten. The
device will not respond to any commands while the
write cycle is in progress.
7.1
Cache Write Starting at a Page
Boundary
If a write command begins at a page boundary
(address bits A2, A1 and A0 are zero), then all data
loaded into the cache will be written to the array in
sequential addresses. This includes writing across a 4K
block boundary. In the example shown below,
(Figure 7-1) a write command is initiated starting at
byte 0 of page 3 with a fully loaded cache (64 bytes).
The first byte in the cache is written to byte 0 of page 3
(of the array), with the remaining pages in the cache
written to sequential pages in the array. A write cycle is
executed after each page is written. Since the write
begins at page 3 and 8 pages are loaded into the
cache, the last 3 pages of the cache are written to the
next row in the array.
7.2
Cache Write Starting at a Non-Page
Boundary
When a write command is initiated that does not begin
at a page boundary (i.e., address bits A2, A1 and A0
are not all zero), it is important to note how the data is
loaded into the cache, and how the data in the cache is
written to the array. When a write command begins, the
first byte loaded into the cache is always loaded into
page 0. The byte within page 0 of the cache where the
load begins is determined by the three least significant
address bits (A2, A1, A0) that were sent as part of the
write command. If the write command does not start at
byte 0 of a page and the cache is fully loaded, then the
last byte(s) loaded into the cache will roll around to
page 0 of the cache and fill the remaining empty bytes.
If more than 64 bytes of data are loaded into the cache,
data already loaded will be overwritten. In the example
shown in Figure 7-2, a write command has been
initiated starting at byte 2 of page 3 in the array with a
fully loaded cache of 64 bytes. Since the cache started
loading at byte 2, the last two bytes loaded into the
cache will ’roll over' and be loaded into the first two
bytes of page 0 (of the cache). When the stop bit is
sent, page 0 of the cache is written to page 3 of the
array. The remaining pages in the cache are then
loaded sequentially to the array. A write cycle is
executed after each page is written. If a partially loaded
page in the cache remains when the STOP bit is sent,
only the bytes that have been loaded will be written to
the array.
7.3
Power Management
The design incorporates a power standby mode when
not in use and automatically powers off after the normal
termination of any operation when a stop bit is received
and all internal functions are complete. This includes
any error conditions, i.e. not receiving an acknowledge
or STOP per the two-wire bus specification. The device
also incorporates V
DD
monitor circuitry to prevent inad-
vertent writes (data corruption) during low-voltage con-
ditions. The V
DD
monitor circuitry is powered off when
the device is in standby mode in order to further reduce
power consumption.
相關PDF資料 |
PDF描述 |
|---|---|
| 24HCA | surface mount silicon Zener diodes |
| 24HCB | surface mount silicon Zener diodes |
| 24HCC | surface mount silicon Zener diodes |
| 24HCD | surface mount silicon Zener diodes |
| 24HC | XTAL PLAS SMT 12X4 4PAD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24FC65/P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24FC65-/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
| 24FC65/SM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24FC65-/SM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
| 24FC65_04 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K 5.0V 1 MHz I2C⑩ Smart Serial⑩ EEPROM |
發布緊急采購，3分鐘左右您將得到回復。