- 您現在的位置：買賣IC網 > PDF目錄371415 > 27210 (Texas Instruments, Inc.) Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR) PDF資料下載
參數資料
| 型號： | 27210 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR) |
| 中文描述： | 鋰離子和鋰聚合物電池電量監測計芯片的便攜式應用（bqJUNIOR） |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 337K |
| 代理商： | 27210 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
Reported Battery Voltage Registers (VOLTL/VOLTH) — Address 0x08/0x09
The VOLTH and the VOLTL low-byte registers contain the reported battery voltage measured on the BAT pin.
Voltage is expressed in mV with an LSB resolution of 1 mV. Reported voltage cannot exceed 5000 mV. The
host system has read-only access to this register pair. Voltage is updated every 2.56 seconds.
Status Flag Register (FLAGS) — Address 0x0A
Relative State-of-Charge (RSOC) — Address 0x0B
RSOC reports the nominal available capacity as a percentage of the last measured discharge value (LMD). The
equation is:
bq27010, bq27210
SLUS707B–APRIL 2006–REVISED JANUARY 2007
BIT 7
CHGS
0
BIT 6
NOACT
0
BIT 5
IMIN
0
BIT 4
CI
1
BIT 3
CALIP
0
BIT 2
VDQ
0
BIT 1
EDV1
0
BIT 0
EDVF
0
NAME
POR STATUS
CHGS
Charge State flag. A
1
in the CHGS indicates a charge current (V
> V
). A
0
indicates a lack
of charge activity. This bit should be read when the host system reads the Average Current
register pair to determine the sign of the average current magnitude. This bit is cleared to
0
on all
resets.
NOACT
No Activity flag. A
1
indicates that the voltage across R
is less than the digital magnitude filter.
See the
Digital Magnitude Filter
section for more information. This bit is cleared to
0
on all resets.
IMIN
Li-ion taper current detection flag. A
1
indicates that the charge current has tapered to less than
the value set in EEPROM and that the battery voltage is greater than or equal to the value
selected by the QV0 and QV1 bits in the PKCFG register (see EEPROM Data Register description
for more details). Taper current detection is disqualified if AI < 8 (28.6 μV across sense resistor).
The
taper
detection
conditions
must
be
maintained
measurements (20-25 s) to qualify as a valid taper current detection. This bit is cleared to
0
on all
resets.
for
4
successive
average
current
CI
Capacity Inaccurate flag. A
1
indicates that the firmware has not been through a valid learning
cycle and is basing all calculations on initial design values programmed into EEPROM or that there
have been at least 32 cycle-count increments since the last learning cycle. This bit is cleared only
on a LMD update following a learning cycle. This bit is set to
1
on a full reset. The previous value
is retained if no RAM corruption is detected after a reset.
CALIP
Calibration-In-Progress flag. This flag is set whenever an automatic or commanded offset
calibration measurement is being made. This bit is set to
0
on all resets.
VDQ
Valid Discharge flag. A
1
indicates that the bqJUNIOR has met all necessary requirements for the
firmware to learn the battery capacity. This bit clears to
0
on a LMD update or condition that
disqualifies a learning cycle. This bit is cleared to
0
on all resets.
EDV1
First End-of-Discharge-Voltage flag. A
1
indicates that the voltage on the BAT pin is less than or
equal to the EDV1 threshold voltage. LMD updates immediately if the VDQ bit is set when this bit
transitions from
0
to 1. This bit is cleared when charging and on all resets.
EDVF
Final End-of-Discharge-Voltage flag. A
1
indicates that the voltage on the BAT pin is less than or
equal to the EDVF threshold voltage. This bit is cleared when charging and on all resets.
The host system has read-only access to this register.
RSOC (%) = 100 * NAC/LMD
The host system has read-only access to this register.
15
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| 270KD05JX | 11 to 460 Volts Varistor 0.7 to 29 Joule |
| 271KD05JX | 11 to 460 Volts Varistor 0.7 to 29 Joule |
| 270KD05NX | 4 to 460 Volts Varistor 0.20 to 22.5 Joule |
| 271KD05NX | 4 to 460 Volts Varistor 0.20 to 22.5 Joule |
| 270KD07NX | 4 to 510 Volts Varistor 0.8 to 47 Joule |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 27-210 | 制造商:Distributed By MCM 功能描述:Chassis Mount Female Solder-On BNC Connector 制造商:MCM 功能描述:RF/COAXIAL, BNC JACK, STRAIGHT, CRIMP; Connector Type:BNC Coaxial; Body Style:Straight Jack; Coaxial Termination:Crimp; Connector Mounting:Panel; Connector Type:BNC Coaxial |
| 272-100 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 272100-11 | 制造商:Amphenol Connex 功能描述:7/16 4HOLE PNL JK .141 LOW PIM - Bulk |
| 272-100-JBW | 制造商:RCD Components Inc 功能描述:Res Wirewound 10 Ohm 5% 10W ±20ppm/°C Molded AXL Thru-Hole Bulk |
| 272101 | 功能描述:RF 連接器 7/16 PANEL JACK .250 S/R 4 HOLE RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
發布緊急采購，3分鐘左右您將得到回復。