- 您現在的位置：買賣IC網 > PDF目錄371438 > 29F001T-12 (Macronix International Co., Ltd.) 1M-BIT [128K x 8] CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29F001T-12 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 1M-BIT [128K x 8] CMOS FLASH MEMORY |
| 中文描述： | 100萬位[128K的× 8]的CMOS閃存 |
| 文件頁數： | 11/42頁 |
| 文件大?。?/td> | 600K |
| 代理商： | 29F001T-12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
11
REV. 2.6, DEC. 29, 2003
P/N: PM0515
MX29F001T/B
Q5
Exceeded Timing Limits
Q5 will indicate if the program or erase time has exceeded
the specified limits(internal pulse count). Under these
conditions Q5 will produce a "1". This time-out condition
indicates that the program or erase cycle was not suc-
cessfully completed. Data Polling and Toggle Bit are the
only operating functions of the device under this condi-
tion.
If this time-out condition occurs during sector erase op-
eration, it is specifies that a particular sector is bad and
it may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other sec-
tors. Write the Reset command sequence to the device,
and then execute program or erase command sequence.
This allows the system to continue to use the other ac-
tive sectors in the device.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or com-
bination of sectors are bad.
If this time-out condition occurs during the byte program-
ming operation, it specifies that the entire sector con-
taining that byte is bad and this sector may not be re-
used, (other sectors are still functional and can be re-
used).
The time-out condition may also appear if a user tries to
program a non blank location without erasing. In this
case the device locks out and never completes the Au-
tomatic Algorithm operation. Hence, the system never
reads a valid data on Q7 bit and Q6 never stops toggling.
Once the Device has exceeded timing limits, the Q5 bit
will indicate a "1". Please note that this is not a device
failure condition since the device was incorrectly used.
Q3
Sector Erase Timer
After the completion of the initial sector erase command
sequence the sector erase time-out will begin. Q3 will
remain low until the time-out is complete. Data Polling
and Toggle Bit are valid after the initial sector erase com-
mand sequence.
If Data Polling or the Toggle Bit indicates the device has
been written with a valid erase command, Q3 may be
used to determine if the sector erase timer window is
still open. If Q3 is high ("1") the internally controlled
erase cycle has begun; attempts to write subsequent
commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or
Toggle Bit. If Q3 is low ("0"), the device will accept addi-
tional sector erase commands. To insure the command
has been accepted, the system software should check
the status of Q3 prior to and following each subsequent
sector erase command. If Q3 were high on the second
status check, the command may not have been accepted.
DATA PROTECTION
The MX29F001T/B is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power transi-
tion. During power up the device automatically resets
the state machine in the Read mode. In addition, with its
control register architecture, alteration of the memory con-
tents only occurs after successful completion of spe-
cific command sequences. The device also incorporates
several features to prevent inadvertent write cycles re-
sulting from VCC power-up and power-down transition or
system noise.
相關PDF資料 |
PDF描述 |
|---|---|
| 29F001T-90 | 1M-BIT [128K x 8] CMOS FLASH MEMORY |
| 29F002B-12 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-55 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-70 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-90 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F001T-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:1M-BIT [128K x 8] CMOS FLASH MEMORY |
| 29F002 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-12 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-55 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 29F002B-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
發布緊急采購，3分鐘左右您將得到回復。