參數資料
型號: 29F004T-70
廠商: Macronix International Co., Ltd.
英文描述: 4M-BIT [512KX8] CMOS FLASH MEMORY
中文描述: 4分位[512KX8]的CMOS閃存
文件頁數: 9/39頁
文件大?。?/td> 599K
代理商: 29F004T-70
9
MX29F004T/B
P/N:PM0554
REV. 1.9, OCT. 19, 2004
SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the de-
vice to be entirely pre-programmed prior to executing
the Automatic Set-up Sector Erase command and Auto-
matic Sector Erase command. Upon executing the Au-
tomatic Sector Erase command, the device will auto-
matically program and verify the sector(s) memory for
an all-zero data pattern. The system is not required to
provide any control or timing during these operations.
When the sector(s) is automatically verified to contain
an all-zero pattern, a self-timed sector erase and verify
begin. The erase and verify operations are complete
when the data on Q7 is "1" and the data on Q6 stops
toggling for two consecutive read cycles, at which time
the device returns to the Read mode. The system is not
required to provide any control or timing during these
operations.
When using the Automatic Sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required). Sector erase
is a six-bus cycle operation. There are two "unlock"
write cycles. These are followed by writing the set-up
command 80H. Two more "unlock" write cycles are then
followed by the sector erase command 30H. The sector
address is latched on the falling edge of WE or CE,
whichever happens later, while the command (data) is
latched on the rising edge of WE or CE, whichever hap-
pens first. Sector addresses selected are loaded into
internal register on the sixth falling edge of WE or CE,
whichever happens later. Each successive sector load
cycle started by the falling edge of WE or CE, which-
ever happens later must begin within 30us from the ris-
ing edge of the preceding WE or CE, whichever hap-
pens first. Otherwise, the loading period ends and inter-
nal auto sector erase cycle starts. (Monitor Q3 to deter-
mine if the sector erase timer window is still open, see
section Q3, Sector Erase Timer.) Any command other
than Sector Erase(30H) or Erase Suspend(B0H) during
the time-out period resets the device to read mode.
Status
Q7
Q6
Q5
Q3
Q2
Note1
Q7
0
1
Note2
0
0
0
Byte Program in Auto Program Algorithm
Auto Erase Algorithm
Toggle
Toggle
No
Toggle
Data
N/A
1
N/A
No Toggle
Toggle
Toggle
Erase Suspend Read
(Erase Suspended Sector)
Erase Suspend Read
(Non-Erase Suspended Sector)
Erase Suspend Program
In Progress
Erase Suspended Mode
Data
Data
Data
Data
Q7
Q7
0
Q7
Toggle
Toggle
Toggle
Toggle
0
1
1
1
N/A
N/A
1
N/A
N/A
Byte Program in Auto Program Algorithm
Auto Erase Algorithm
Time Limits Erase Suspend Program
No Toggle
Toggle
N/A
Exceeded
TABLE 4. WRITE OPERATION STATUS
Note:
1. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
2. Q5 switches to '1' when an Auto Program or Auto Erase operation has exceeded the maximum timing limits.
See "Q5:Exceeded Timing Limits " for more information.
相關PDF資料
PDF描述
29F004T-90 4M-BIT [512KX8] CMOS FLASH MEMORY
29F016-12 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY
29F016-90 16M-BIT [2M X 8] CMOS EQUAL SECTOR FLASH MEMORY
29F022B-12 2M-BIT[256K x 8]CMOS FLASH MEMORY
29F022B-120 2M-BIT[256K x 8]CMOS FLASH MEMORY
相關代理商/技術參數
參數描述
29F004T-90 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512KX8] CMOS FLASH MEMORY
29F010 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Mbit 128Kb x8, Uniform Block Single Supply Flash Memory
29F01045JC 制造商: 功能描述: 制造商:Advanced Micro Devices 功能描述: 制造商:undefined 功能描述:
29F010-45JC 制造商: 功能描述: 制造商:undefined 功能描述:
29F010B55EI 制造商: 功能描述: 制造商:Advanced Micro Devices 功能描述: