- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV320BTC-70 (Macronix International Co., Ltd.) 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29LV320BTC-70 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 32位4米× 8 / 2米× 16]單電壓3V時僅閃存 |
| 文件頁數： | 14/63頁 |
| 文件大?。?/td> | 949K |
| 代理商： | 29LV320BTC-70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
14
P/N:PM0742
REV. 1.4, JUL. 04, 2003
MX29LV320T/B
ing used to replace devices that are factory locked.
The system accesses the Security Sector through a
command sequence (see "Enter Security Sector/Exit
Security Sector Command Sequence"). After the sys-
tem has written the Enter Security Sector command se-
quence, it may read the Security Sector by using the ad-
dresses normally occupied by the boot sectors. This
mode of operation continues until the system issues the
Exit Security Sector command sequence, or until power
is removed from the device. On power-up, or following a
hardware reset, the device reverts to sending commands
to the boot sectors.
Factory Locked: Security Sector Programmed
and Protected at the Factory
In a factory locked device, the Security Sector is pro-
tected when the device is shipped from the factory. The
Security Sector cannot be modified in any way. The de-
vice is available preprogrammed with one of the follow-
ing:
A random, secure ESN only.
Customer code through the Express Flash service.
Both a random, secure ESN and customer code through
the Express Flash service.
In devices that have an ESN, a Bottom Boot device will
have the 16-byte (8-word) ESN in the lowest address-
able memory area starting at 00000h and ending at
0000Fh (00007h). In the Top Boot device the starting
address of the ESN will be at the bottom of the lowest 8
Kbyte (4 Kword) boot sector starting at 3F0000h
(1F8000h) and ending at 3F000Fh (1F8007h).
Customer Lockable: Security Sector NOT Pro-
grammed or Protected at the Factory
If the security feature is not required, the Security Sec-
tor can be treated as an additional Flash memory space,
expanding the size of the available Flash array by 64
Kbytes (32 Kwords). The Security Sector can be read,
programmed, and erased as often as required. The Se-
curity Sector area can be protected using one of the
following procedures:
Write the three-cycle Enter Security Region command
sequence, and then follow the in-system sector group
protect algorithm as shown in Figure 17, except that
RESET may be at either VIH or V
. This allows in-sys-
tem protection of the without raising any device pin to a
high voltage. Note that this method is only applicable to
the Security Sector.
Write the three-cycle Enter Security Region command
sequence, and then use the alternate method of sector
protection described in the "Sector/Sector Block Protec-
tion and Unprotection section.
Once the Security Sector is locked and verified, the sys-
tem must write the Exit Security Sector Region com-
mand sequence to return to reading and writing the re-
mainder of the array.
The Security Sector protection must be used with cau-
tion since, once protected, there is no procedure avail-
able for unprotecting the Security Sector area and none
of the bits in the Security Sector memory space can be
modified in any way.
DATA PROTECTION
The MX29LV320T/B is designed to offer protection
against accidental erasure or programming caused by
spurious system level signals that may exist during power
transition. During power up the device automatically re-
sets the state machine in the Read mode. In addition,
with its control register architecture, alteration of the
memory contents only occurs after successful comple-
tion of specific command sequences. The device also
incorporates several features to prevent inadvertent write
cycles resulting from VCC power-up and power-down tran-
sition or system noise.
LOW VCC WRITE INHIBIT
When VCC is less than VLKO the device does not ac-
cept any write cycles. This protects data during VCC
power-up and power-down. The command register and
all internal program/erase circuits are disabled, and the
device resets. Subsequent writes are ignored until VCC
is greater than VLKO. The system must provide the proper
signals to the control pins to prevent unintentional write
when VCC is greater than VLKO.
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 5ns (typical) on OE, CE or WE
will not initiate a write cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| 29LV400C-55R | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV650 | 64M (4M x 16) BIT |
| 29LV800BB-70 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29LV400BA | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 29LV400C-55R | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV51215JU | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。