- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV320BTC-70 (Macronix International Co., Ltd.) 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29LV320BTC-70 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 32位4米× 8 / 2米× 16]單電壓3V時僅閃存 |
| 文件頁數： | 19/63頁 |
| 文件大小： | 949K |
| 代理商： | 29LV320BTC-70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
19
P/N:PM0742
REV. 1.4, JUL. 04, 2003
MX29LV320T/B
SECTOR ERASE COMMANDS
The device does not require the system to entirely
pre-program prior to executing the Automatic Set-up
Sector Erase command and Automatic Sector Erase
command. Upon executing the Automatic Sector
Erase command, the device will automatically
program and verify the sector(s) memory for an all-
zero data pattern. The system is not required to
provide any control or timing during these operations.
When the sector(s) is automatically verified to
contain an all-zero pattern, a self-timed sector erase
and verify begin. The erase and verify operations are
complete when the data on Q7 is "1" and the data on
Q6 stops toggling for two consecutive read cycles, at
which time the device returns to the Read mode. The
system is not required to provide any control or timing
during these operations.
When using the Automatic Sector Erase algorithm,
note that the erase automatically terminates when
adequate erase margin has been achieved for the
memory array (no erase verification command is
required). Sector erase is a six-bus cycle operation.
There are two "unlock" write cycles. These are
followed by writing the set-up command 80H. Two
more "unlock" write cycles are then followed by the
sector erase command 30H. The sector address is
latched on the falling edge of WE or CE, whichever
happens later , while the command(data) is latched on
the rising edge of WE or CE, whichever happens first.
Sector addresses selected are loaded into internal
register on the sixth falling edge of WE or CE,
whichever happens later. Each successive sector
load cycle started by the falling edge of WE or CE,
whichever happens later must begin within 50us from
the rising edge of the preceding WE or CE, whichever
happens first. Otherwise, the loading period ends and
internal auto sector erase cycle starts. (Monitor Q3 to
determine if the sector erase timer window is still
open, see section Q3, Sector Erase Timer.) Any
command other than Sector Erase(30H) or Erase
Suspend(B0H) during the time-out period resets the
device to read mode.
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. When the Erase Suspend com-
mand is issued during the sector erase operation, the
device requires a maximum 20us to suspend the sector
erase operation. However, When the Erase Suspend com-
mand is written during the sector erase time-out, the
device immediately terminates the time-out period and
suspends the erase operation. After this command has
been executed, the command register will initiate erase
suspend mode. The state machine will return to read
mode automatically after suspend is ready. At this time,
state machine only allows the command register to re-
spond to the Erase Resume, program data to, or read
data from any sector not selected for erasure. The sys-
tem can use Q7, or Q6 and Q2 together, to determine if
a sector is actively erasing or is erase-suspended.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended blocks.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
相關PDF資料 |
PDF描述 |
|---|---|
| 29LV400C-55R | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV650 | 64M (4M x 16) BIT |
| 29LV800BB-70 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29LV400BA | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 29LV400C-55R | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV51215JU | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。