- 您現在的位置：買賣IC網 > PDF目錄371440 > 29LV320BTC-70 (Macronix International Co., Ltd.) 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29LV320BTC-70 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 32位4米× 8 / 2米× 16]單電壓3V時僅閃存 |
| 文件頁數： | 17/63頁 |
| 文件大?。?/td> | 949K |
| 代理商： | 29LV320BTC-70 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
17
P/N:PM0742
REV. 1.4, JUL. 04, 2003
MX29LV320T/B
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. After
completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See Erase Suspend/Erase
Resume Commands” for more information on this mode.
The system
must
issue the reset command to re-en-
able the device for reading array data if Q5 goes high
during an active program or erase operation, or while in
the Automatic Select mode. See the "Reset Command"
section, next.
RESET COMMAND
Writing the reset command to the device resets the
device to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence before
programming begins. This resets the device to reading
array data (also applies to programming in Erase Suspend
mode). Once programming begins, however, the device
ignores reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in an Automatic Select command
sequence. Once in the Automatic Select mode, the reset
command
must
be written to return to reading array data
(also applies to Automatic Select during Erase Suspend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to read-ing
array data (also applies during Erase Suspend).
AUTOMATIC SELECT COMMAND SEQUENCE
The Automatic Select command sequence allows the
host system to access the manufacturer and device
codes, and determine whether or not a sector is pro-
tected. Table 2 shows the address and data requirements.
This method is an alternative to that shown in Table 3,
which is intended for EPROM programmers and requires
V
ID
on address bit A9.
The Automatic Select command sequence is initiated
by writ-ing two unlock cycles, followed by the Automatic
Select command. The device then enters the Automatic
Select mode, and the system may read at any address
any number of times, without initiating another command
sequence. A read cycle at address XX00h retrieves the
manufacturer code. A read cycle at address XX01h in
word mode (or xx02h in byte mode) returns the device
code. A read cycle containing a sector address (SA) and
the address 02h on A7-A0 in word mode (or the address
04h on A6-A-1 in byte mode) returns 01h if that sector is
protected, or 00h if it is unprotected. Refer to Table 1 for
valid sector addresses.
The system must write the reset command to exit the
Automatic Select mode and return to reading array data.
ENTER SECURITY SECTOR & EXIT SECURITY
SECTOR COMMAND SEQUENCE
The Security Sector provides a secured area which con-
tains a random, sixteen-byte electronic serial
number.(ESN)
The system can access the Security Sector area by is-
suing the three-cycle "Enter Security Sector command
sequence. The device continues to access the security
section area until the system issues the four-cycle Exit
Security Sector command sequence. The Exit Security
Sector command sequence returns the device to normal
operation.
BYTE/WORD PROGRAM COMMAND SEQUENCE
The device programs one byte/word of data for each
program operation. The command sequence requires four
bus cycles, and is initiated by writing two unlock write
cycles, followed by the program set-up command. The
program address and data are written next, which in turn
initiate the Embedded Program algorithm. The system is
not
required to provide further controls or timings. The
device automatically generates the program pulses and
相關PDF資料 |
PDF描述 |
|---|---|
| 29LV400C-55R | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV650 | 64M (4M x 16) BIT |
| 29LV800BB-70 | 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29LV400BA | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 29LV400C-55R | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV400C-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 29LV51215JU | 制造商: 功能描述: 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。