參數資料
型號： 5962-8967401QX
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： ADC
英文描述： 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP40
封裝： CERAMIC, DIP-40
文件頁數： 24/34頁
文件大?。?/td> 860K
代理商： 5962-8967401QX
MAX5580–MAX5585
Buffered, Fast-Settling, Quad,
12-/10-/8-Bit, Voltage-Output DACs
30
______________________________________________________________________________________
GPI, GPOL, GPOH
UPIO1 and UPIO2 can each be configured as a gener-
al-purpose input (GPI), a general-purpose output low
(GPOL), or a general-purpose output high (GPOH).
The GPI can serve to detect interrupts from Ps or micro-
controllers. The GPI has three functions:
1) Sample the signal at GPI at the time of the read
(RTP1 and RTP2).
2) Detect whether a falling edge has occurred since
the last read or reset (LF1 and LF2).
3) Detect whether a rising edge has occurred since
the last read or reset (LR1 and LR2).
RTP1, LF1, and LR1 represent the data read from
UPIO1; RTP2, LF2, and LR2 represent the data read
from UPIO2.
To issue a read command for the UPIO configured as
GPI, use the command in Table 22.
Once the command is issued, RTP1 and RTP2 provide
the real-time status (0 or 1) of the inputs at UPIO1 or
UPIO2, respectively, at the time of the read. If LF2 or
LF1 is one, then a falling edge has occurred on the
respective UPIO1 or UPIO2 input since the last read or
reset. If LR2 or LR1 is one, then a rising edge has
occurred since the last read or reset.
GPOL outputs a constant low, and GPOH outputs a
constant high. See Figure 6.
TOGG
Use the TOGG input to toggle the DAC outputs
between the values in the input registers and DAC reg-
isters. A delay of greater than 100ns from the end of the
previous write command is required before the TOGG
signal can be correctly switched between the new
value and the previously stored value. When TOGG =
0, the output follows the information in the input regis-
ters. When TOGG = 1, the output follows the informa-
tion in the DAC register (Figure 5).
FAST
The MAX5580–MAX5585 have two settling-time-mode
options: FAST (3s max) and SLOW (6s max). To
select the FAST mode, drive FAST low, and to select
SLOW mode, drive FAST high. This overrides (not over-
writes) the SPDA–SPDD bit settings.
Table 22. GPI Read Command
DATA
CONTROL BITS
DATA BITS
DIN
1
11001
XXXXX
XXXX
DOUTRB
X
XXXXX
XXX
RTP2
LF2
LR2
RTP1
LF1
LR1
Table 23. Unipolar Code Table (Gain = +1)
DAC CONTENTS
MSB
LSB
ANALOG OUTPUT
1111
+VREF (4095 / 4096)
1000
0000
0001
+VREF (2049 / 4096)
1000
0000
+VREF (2048 / 4096) = VREF / 2
0111
1111
+VREF (2047 / 4096)
0000
0001
+VREF (1 / 4096)
0000
0
MAX5580
DAC_
REF
OUT_
VOUT_ = VREF_ x CODE / 4096
WHERE CODE IS THE DAC INPUT
CODE (0 TO 4095 DECIMAL)
MAX6126
Figure 7. Unipolar Output Circuit
X = Don’t care.
相關PDF資料
PDF描述
5962-8967402QX 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP40
5962-8967402XX 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CQCC44
5962-8967601QX 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP40
5962-8967601QX 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CDIP40
5962-8967601XX 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL/PARALLEL ACCESS, CQCC44
相關代理商/技術參數
參數描述
5962-8967701CA 制造商:Linear Technology 功能描述:AMPLIFIER-OP AMP 制造商:Texas Instruments 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP AMP QUAD GP 22V/44V 14CDIP - Rail/Tube 制造商:Texas Instruments 功能描述:LT1014AMJB QUAD PREC OP AMP
5962-8967702CA 制造商:Texas Instruments 功能描述:OP Amp Quad GP ±22V/44V 14-Pin CDIP Tube 制造商:Texas Instruments 功能描述:OP AMP QUAD GP 22V/44V 14CDIP - Rail/Tube
5962-8967801XA 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
5962-8967802XA 制造商:Rochester Electronics LLC 功能描述:8-BIT QUAD MULT DAC IC - Bulk 制造商:Analog Devices 功能描述:
5962-8967901XC 制造商:SEI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*