- 您現在的位置：買賣IC網 > PDF目錄24836 > 935289802118 (NXP SEMICONDUCTORS) LED DISPLAY DRIVER, PDSO28 PDF資料下載
參數資料
| 型號： | 935289802118 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED DISPLAY DRIVER, PDSO28 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT361-1, TSSOP-28 |
| 文件頁數： | 5/54頁 |
| 文件大?。?/td> | 410K |
| 代理商： | 935289802118 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
PCA9685_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 16 July 2009
13 of 50
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I2C-bus LED controller
7.3.1 Mode register 1, MODE1
[1]
When the Auto Increment ag is set, AI = 1, the Control register is automatically incremented after a read or write. This allows the user
to program the registers sequentially.
[2]
It takes 500
s max. for the oscillator to be up and running once SLEEP bit has been set to logic 0. Timings on LEDn outputs are not
guaranteed if PWM control registers are accessed within the 500
s window. There is no start-up delay required when using the
EXTCLK pin as the PWM clock.
[3]
No PWM control is possible when the oscillator is off.
[4]
When the oscillator is off (Sleep mode) the LEDn outputs cannot be turned on, off or dimmed/blinked.
Table 4.
MODE1 - Mode register 1 (address 00h) bit description
Legend: * default value.
Bit
Symbol
Access
Value
Description
7
RESTART
R
Shows state of RESTART logic. See Section 7.3.1.1 for detail.
W
User writes logic 1 to this bit to clear it to logic 0. A user write of logic 0 will have no
effect. See Section 7.3.1.1 for detail.
0*
Restart disabled.
1
Restart enabled.
6
EXTCLK
R/W
To use the EXTCLK pin, this bit must be set by the following sequence:
1. Set the SLEEP bit in MODE1. This turns off the internal oscillator.
2. Write logic 1s to both the SLEEP and EXTCLK bits in MODE1. The switch is
now made. The external clock can be active during the switch because the
SLEEP bit is set.
This bit is a ‘sticky bit’, that is, it cannot be cleared by writing a logic 0 to it. The
EXTCLK bit can only be cleared by a power cycle or software reset.
EXTCLK range is DC to 50 MHz.
0*
Use internal clock.
1
Use EXTCLK pin clock.
5
AI
R/W
0*
Register Auto-Increment disabled[1].
1
Register Auto-Increment enabled.
4
SLEEP
R/W
0
Normal mode[2].
1*
Low power mode. Oscillator off[3][4].
3
SUB1
R/W
0*
PCA9685 does not respond to I2C-bus subaddress 1.
1
PCA9685 responds to I2C-bus subaddress 1.
2
SUB2
R/W
0*
PCA9685 does not respond to I2C-bus subaddress 2.
1
PCA9685 responds to I2C-bus subaddress 2.
1
SUB3
R/W
0*
PCA9685 does not respond to I2C-bus subaddress 3.
1
PCA9685 responds to I2C-bus subaddress 3.
0
ALLCALL
R/W
0
PCA9685 does not respond to LED All Call I2C-bus address.
1*
PCA9685 responds to LED All Call I2C-bus address.
refresh_rate
EXTCLK
4096
prescale
1
+
()
×
-------------------------------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| 935288883112 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935288883115 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935288883118 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935085330112 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
| 935085330115 | DATACOM, INTERFACE CIRCUIT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9-3528-TP | 制造商:Keystone Electronics Corp 功能描述: |
| 935290014599 | 制造商:NXP Semiconductors 功能描述:KIT OM12097 |
| 935290808118 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH 8CH 16TSSOP |
| 935290809118 | 制造商:NXP Semiconductors 功能描述:IC ANALOG SWITCH SPDT 16TSSOP |
| 935290874112 | 制造商:NXP Semiconductors 功能描述:IC PWR AMP I2C BUS CTRL DBS27P |
發布緊急采購，3分鐘左右您將得到回復。