參數資料
型號： ACE9030
廠商： Mitel Networks Corporation
英文描述： Radio Interface and Twin Synthesiser(用于蜂窩式電話的無線電接口電路和雙合成器)
中文描述： 無線接口和雙合成器（用于蜂窩式電話的無線電接口電路和雙合成器）
文件頁數： 14/39頁
文件大?。?/td> 379K
代理商： ACE9030
14
ACE9030
Data is accepted by the circuit on the rising edge of
LATCHC. Programmable divider ratios will be changed at their
next re-load, at up to a whole comparison period after the
LATCHC edge.
Normal channel changes require only word A but if it is
necessary to maintain exactly uniform loop dynamics the
parameter CN (see Main Synthesiser - Normal Mode) must
also change. This can be achieved by either sending a word
B for the CN parameter before word A for the frequency or
alternatively the extended command A2 can be used to
combine both in one long word. This A2 mode is not supported
by the ACE9050 as it is not necessary for most cellular
terminals.
If Word B is reprogrammed, the new values do not
become effective until the next Word A is written. This
prevents any spurious conditions during a channel change.
The LG bit in Word D sets whether A or A2 mode is to be
used, 0 for A and 1 for A2.
Speed-up drive is active for the duration of the LATCHC
pulse that loads the A or A2 word and if it is required the pulse
will typically be hundreds of cycles of CL in duration.
In some applications the system performance can be
improved by holding LATCHC at HIGH to minimise clock noise
on the synthesisers. LATCHC also controls Speed-up mode
and so to exit speed-up mode after a channel change the
LATCHC must be driven LOW and then a dummy command
can be added to get LATCHC back to HIGH. This dummy
command should be a non-functional word formed by setting
the last four bits to 1111 as in figure 11; the value or the number
of the data bits before the four 1’s are of no significance so the
typical schemes are to send either a standard 24 bit message
ending 1111 or a special 4 bit only message of 1111 and in
both cases the LATCHC is kept HIGH until the next channel
change.
The TEST bits in Word B must be set to 0000 for normal
operation and the first two bits in Word B should be set to 00
to be sure of compatibility with future variants.
Summary of Synthesiser Programming
BIT STRING
N1
N2
NF
TEST
Range of values
3 - 4095
1 - 255
0 - 7
0000
FUNCTION
Main synthesiser down count; prescaler at lower modulus.
Main synthesiser up count; prescaler at higher modulus.
Main synthesiser fractional increment numerator.
This state must be selected in every Word B for normal operation.
TEST pin will be held LOW to screen adjacent PDA pin.
Other test modes are for use during chip manufacture only.
Main charge pump current scaling coefficient.
Integral charge pump speed-up mode multiplying factor.
Proportional charge pump speed-up mode exponent, giving x 2, x4, x 8
or x 16 current.
Auxiliary synthesiser VCO divider ratio.
Reference divider ratio.
Main synthesiser comparison frequency select.
Main synthesiser in standby mode if DM set HIGH.
Auxiliary synthesiser comparison frequency select.
Auxiliary synthesiser in standby mode if DA set HIGH.
Fractional-N denominator,
1
/
5
’s when at “0” or
1
/
8
’s when at “1”.
Control bus mode select - Word A if LOW or Word A2 if HIGH.
CN
K
L
0 - 255
0 - 15
0 - 3
NA
NR
SM
DM
SA
DA
FMOD
LG
3 - 4095
8 - 4095
0 - 3
0, 1
0 - 3
0, 1
0, 1
0, 1
相關PDF資料
PDF描述
ACE9030 Radio Interface and Twin Synthesiser
ACE9040 Audio Processor Advance Information
ACE9050 System Controller and Data Modem(為蜂窩式手機提供控制和邏輯接口功能的系統控制器和數據調制解調器)
ACE9050 System Controller and Data Modem Advance Information
ACFA-450 AM CERAMIC FILTERS
相關代理商/技術參數
參數描述
ACE9030IGFP1N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel-Input Frequency Synthesizer
ACE9030IGFP1R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel-Input Frequency Synthesizer
ACE9030IGFP2N 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel-Input Frequency Synthesizer
ACE9030IGFP2R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel-Input Frequency Synthesizer
ACE9030M 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Radio Interface and Twin Synthesiser
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*