參數資料
型號： AD1941YSTZRL
廠商： Analog Devices Inc
文件頁數： 4/36頁
文件大小： 0K
描述： IC DSP AUDIO 16CHAN 28BIT 48LQFP
標準包裝： 2,000
系列： SigmaDSP®
類型： 音頻處理器
應用： 車載系統，家庭影院，電視
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 帶卷 (TR)
AD1940/AD1941
Rev. B | Page 12 of
36
PIN FUNCTIONS
Table 10 shows the AD1940/AD1941’s pin numbers, names, and
functions. Input pins have a logic threshold compatible with
TTL input levels and may be used in systems with 3.3 V or
5 V logic.
SDATA_IN0
SDATA_IN1
SDATA_IN2/TDM_IN1
SDATA_IN3/TDM_IN0
Serial Data/TDM Inputs. The serial format is selected by
writing to Bits 2:0 of the serial input port control register.
SDATA_IN2 and SDATA_IN3 are dual-function pins that can
be set to a variety of standard 2-channel formats or to TDM
mode. Two of these four pins (SDATA_IN2 and SDATA_IN3)
can be used as TDM inputs in either dual-wire 8-channel mode
or single-wire 16-channel mode (TDM_O0 only). In dual-wire
8-channel mode, Channels 0 to 7 are input on SDATA_IN3 and
Channels 8 to 15 on SDATA_IN2. In single-wire 16-channel
mode, Channels 0 to 15 are input on SDATA_IN2. See the
Serial Data Input/Output Ports section for further explanation.
LRCLK_IN
BCLK_IN
Left/Right and Bit Clocks for Timing the Input Data. These
input clocks are associated with the SDATA_IN0 through
SDATA_IN3 signals. The input port is always in a slave
configuration. These pins also function as frame sync and bit
clock for the input TDM stream.
SDATA_OUT0/TDM_O0
SDATA_OUT1
SDATA_OUT2
SDATA_OUT3
SDATA_OUT4/TDM_O1
SDATA_OUT5
SDATA_OUT6
SDATA_OUT7/DCSOUT
Serial Data/TDM/Data Capture Outputs. These pins are used
for serial digital outputs. For non-TDM systems, these eight
pins can output 16 channels of digital audio, using a variety of
standard 2-channel formats. They are grouped into two groups
of four pins (Pins 0 to 3 and Pins 4 to 7); each group can be
independently set to any of the available serial modes, allowing
the AD1940/AD1941 to simultaneously communicate with two
external devices with different serial formats. Two of these eight
pins (SDATA_OUT0 and SDATA_OUT4) can be used as TDM
outputs in either dual-wire 8-channel mode or single-wire 16-
channel mode (TDM_OUT0 only). In dual-wire 8-channel
mode, Channels 0 to 7 are output on SDATA_OUT0 and
Channels 8 to 15 on SDATA_OUT4. See the Serial Data
Input/Output Ports section for further explanation.
SDATA_OUT7 can also be used as a data capture output, as
described in the Data Capture Registers section.
LRCLK_OUT0
BCLK_OUT0
Output Clocks. This clock pair is used for outputs
SDATA_OUT0 through SDATA_OUT3. In slave mode, these
clocks are inputs to the AD1940/AD1941. On power-up, these
pins are set to slave mode to avoid conflicts with external
master mode devices.
LRCLK_OUT1
BCLK_OUT1
Output Clocks. This clock pair is used for outputs
SDATA_OUT4 through SDATA_OUT7. In slave mode, these
clocks are inputs to the AD1940/AD1941. On power-up, these
pins are set to slave mode to avoid conflicts with external
master mode devices.
MCLK
Master Clock Input. The AD1940/AD1941 uses a PLL to
generate the appropriate internal clock for the DSP core. An
in-depth description of using the PLL is found in the Setting
PLL_CTRL0
PLL_CTRL1
PLL_CTRL2
PLL Mode Control Pins. The functionality of these pins is
described in the Setting Master Clock/PLL Mode section.
CDATA (AD1940)
Serial Data Input for the SPI Control Port.
COUT (AD1940)
Serial Data Output for the SPI Port. This is used for reading
back registers and memory locations. It is three-stated when an
SPI read is not active.
CCLK (AD1940)
SPI Bit Clock. This clock may either run continuously or be
gated off between SPI transactions.
CLATCH (AD1940)
SPI Latch Signal. This must go low at the beginning of an SPI
transaction and high at the end of a transaction. Each SPI
transaction may take a different number of CCLKs to complete,
depending on the address and read/write bit that are sent at the
beginning of the SPI transaction.
SCL (AD1941)
I2C Clock. This pin is always an input because the AD1941
cannot act as a master on the I2C bus. The line connected to this
pin should have a 2 kΩ pull-up resistor on it.
SDA (AD1941)
I2C Serial Data. The data line is bidirectional. The line
connected to this pin should have a 2 kΩ pull-up resistor on it.
相關PDF資料
PDF描述
AD1940YSTZRL IC DSP AUDIO 16CH/28BIT 48-LQFP
SP3243EUEA-L/TR IC TXRX RS232 INTELLIGENT 28SSOP
VE-21J-IU-F2 CONVERTER MOD DC/DC 36V 200W
ADAU1446YSTZ-3A-RL IC SIGMADSP 175MHZ 100LQFP
SP3243EUCA-L/TR IC TXRX RS232 INTELLIGENT 28SSOP
相關代理商/技術參數
參數描述
AD1953 制造商:AD 制造商全稱:Analog Devices 功能描述:SigmaDSP⑩ 3-Channel, 26-Bit Signal Processing DAC
AD1953YST 制造商:Analog Devices 功能描述:DAC 3-CH Delta-Sigma 24-bit 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:3 CHANNEL 24 BIT SIGNAL-PROCESSING DAC - Tape and Reel 制造商:Analog Devices 功能描述:IC 24BIT DAC SMD 1953 LQFP48
AD1953YSTRL 制造商:Analog Devices 功能描述:DAC 3-CH Delta-Sigma 24-bit 48-Pin LQFP T/R
AD1953YSTRL7 制造商:Analog Devices 功能描述:DAC 3-CH Delta-Sigma 24-bit 48-Pin LQFP T/R 制造商:Rochester Electronics LLC 功能描述:3 CHANNEL 24 BIT SIGNAL-PROCESSING DAC - Tape and Reel
AD1953YSTZ 功能描述:IC DSP DAC AUDIO3CH/26BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SigmaDSP® 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*