- 您現在的位置：買賣IC網 > PDF目錄8575 > AD5392BCPZ-5 (Analog Devices Inc)IC DAC 14BIT 8CHAN 5V 64LFCSP PDF資料下載
參數資料
| 型號： | AD5392BCPZ-5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/44頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 8CHAN 5V 64LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | AD5390/1/2 Redesign Change 16/May/2012 |
| 設計資源： | 8 to 16 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5390/1/2 (CN0029) AD5390/91/92 Channel Monitor Function (CN0030) |
| 標準包裝： | 1 |
| 設置時間： | 8µs |
| 位數： | 14 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 16 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 35mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 8 電壓，單極 |
| 采樣率（每秒）： | 125k |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Data Sheet
AD5390/AD5391/AD5392
Rev. E | Page 27 of 44
I2C SERIAL INTERFACE
The AD5390/AD5391/AD5392 feature an I2C-compatible
2-wire interface consisting of a serial data line (SDA) and a
serial clock line (SCL). SDA and SCL facilitate communication
between the DACs and the master at rates up to 400 kHz.
Figure 6 shows the 2-wire interface timing diagram.
When selecting the I2C operating mode by configuring the
SPI/I2C pin to Logic 0, the device is connected to the I2C bus
as a slave device, that is, no clock is generated by the device.
The AD5390/AD5391/AD5392 have a 7-bit slave address 1010 1
(AD1)(AD0). The five MSBs are hard-coded and the two LSBs
are determined by the state of the AD1 and AD0 pins. The
hardware configuration facility for the AD1 and AD0 pins
allows four of these devices to be configured on the bus.
I2
One data bit is transferred during each SCL clock cycle. The
data on SDA must remain stable during the high period of the
SCL clock pulse. Changes in SDA while SCL is high are control
signals that configure START and STOP conditions. Both SDA
and SCL are pulled high by the external pull-up resistors when
the I2C bus is not busy.
START and STOP Conditions
A master device initiates communication by issuing a START
condition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high trans-
ition on SDA, while SCL is high. A START condition from the
master signals the beginning of a transmission to the AD539x.
The STOP condition frees the bus. If a repeated START
condition (Sr) is generated instead of a STOP condition, the
bus remains active.
Repeated START Condition
A repeated START (Sr) condition may indicate a change of data
direction on the bus. Sr may be used when the bus master is
writing to several I2C devices and does not want to relinquish
control of the bus.
Acknowledge Bit (ACK)
The acknowledge bit (ACK) is the ninth bit attached to any 8-bit
data-word. An ACK is always generated by the receiving device.
The AD539x devices generate an ACK when receiving an address
or data by pulling SDA low during the ninth clock period.
Monitoring the ACK allows for detection of unsuccessful data
transfers. An unsuccessful data transfer occurs if a receiving
device is busy or if a system fault has occurred. In the event of
an unsuccessful data transfer, the bus master should reattempt
communication.
AD539X Slave Addresses
A bus master initiates communication with a slave device by
issuing a START condition followed by the 7-bit slave address.
When idle, the AD539x device waits for a START condition
followed by its slave address. The LSB of the address word is
the read/write (R/W) bit. The AD539x devices are receive
devices only and R/W = 0 when communicating with them.
After receiving the proper address 1010 1(AD1) (AD0), the
AD539x issues an ACK by pulling SDA low for one clock cycle.
The AD539x has four user-programmable addresses determined
by the AD1 and AD0 bits.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5570BRSZ-REEL7 | IC DAC 16BIT SERIAL IN 16SSOP |
| AD5570BRSZ-REEL | IC DAC 16BIT SERIAL IN 16SSOP |
| AD7538AQ | IC DAC 14BIT W/BUFF 24-CDIP |
| VE-B52-MU | CONVERTER MOD DC/DC 15V 200W |
| AD7537JR | IC DAC 12BIT DUAL MULT 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5392BST-3 | 制造商:Analog Devices 功能描述:DAC 8CH RES-STRING 14BIT 52LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8-CHN 3V SINGLE SUPPLY 14-BIT VOUT I.C. - Bulk |
| AD5392BST-5 | 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 52-Pin LQFP 制造商:Analog Devices 功能描述:14BIT DAC 8CH 5V SMD 5392 LQFP52 |
| AD5392BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 52-Pin LQFP T/R |
| AD5392BSTZ-3 | 功能描述:IC DAC 14BIT 8CHAN 3V 52LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5392BSTZ-5 | 功能描述:IC DAC 14BIT 8CHAN 3V 52LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
發布緊急采購，3分鐘左右您將得到回復。