- 您現在的位置：買賣IC網 > PDF目錄8575 > AD5392BCPZ-5 (Analog Devices Inc)IC DAC 14BIT 8CHAN 5V 64LFCSP PDF資料下載
參數資料
| 型號： | AD5392BCPZ-5 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 28/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT 8CHAN 5V 64LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 產品變化通告： | AD5390/1/2 Redesign Change 16/May/2012 |
| 設計資源： | 8 to 16 Channels of Programmable Voltage with Excellent Temperature Drift Performance Using AD5390/1/2 (CN0029) AD5390/91/92 Channel Monitor Function (CN0030) |
| 標準包裝： | 1 |
| 設置時間： | 8µs |
| 位數： | 14 |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 16 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 35mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 8 電壓，單極 |
| 采樣率（每秒）： | 125k |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD5390/AD5391/AD5392
Data Sheet
Rev. E | Page 34 of 44
Table 27 shows the control register contents of the AD5391. Table 28 provides bit descriptions. Note that REG1 = REG0 = 0,
A3 to A0 = 1100, and DB13 to DB0 contain the control register data.
Table 27. AD5391 Control Register Contents
MSB
LSB
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Table 28. AD5391 Bit Descriptions
Bit
Description
CR11
Power-Down Status. This bit is used to configure the output amplifier state in power-down mode.
CR11 = 1: Amplifier output is high impedance (default on power-up).
CR11 = 0: Amplifier output is 100 kΩ to ground.
CR10
REF Select. This bit selects the operating internal reference for the AD5391. CR10 is programmed as follows:
CR10 = 1: Internal reference is 2.5 V (AD5391-5 default). Recommended operating reference for AD5391-5.
CR10 = 0: Internal reference is 1.25 V (AD5391-3 default). Recommended operating reference for AD5391-3.
CR9
Current Boost Control. This bit is used to boost the current in the output amplifier, thus altering its slew rate. This bit is
configured as follows:
CR9 = 1: Boost mode on. This maximizes the bias current in the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR9 = 0: Boost mode off (default on power-up). This reduces the bias current in the output amplifier and reduces the overall
power consumption.
CR8
Internal/External Reference. This bits determines if the DAC uses its internal reference or an external reference.
CR8 = 1: Internal reference enabled. Reference output depends on data loaded to CR10.
CR8 = 0: External reference selected (default on power-up).
CR7
Channel Monitor Enable (see Table 24).
CR7 = 1: Monitor enabled. This enables the channel monitor function. Following a write to the monitor channel in
the SFR register, the selected channel output is routed to the MON_OUT pin.
CR7 = 0: Monitor disabled (default on power-up). When monitor is disabled, the MON_OUT pin is three-stated.
CR6
Thermal Monitor Function. When enabled, this function is used to monitor the internal die temperature of the AD5391,
when enabled. The thermal monitor powers down the output amplifiers when the temperature exceeds 130°C. This function
can be used to protect the device in cases where the power dissipation of the device may be exceeded, if a number of
output channels are simultaneously short circuited. A soft power-up re-enables the output amplifiers if the die temperature
has dropped below 130°C.
CR6 = 1: Thermal monitor enabled.
CR6 = 0: Thermal monitor disabled (default on power-up).
CR5 to CR2
Don’t Care.
CR1 to CR0
Toggle Function Enable. This function lets the user toggle the output between two codes loaded to the A and B register for
each DAC. Control Register Bit CR1 and Bit CR0 are used to enable individual groups of eight channels for operation in
toggle mode on the AD5391, as follows:
CR1
Group 1
Channel 8 to Channel 15
CR0
Group 0
Channel 0 to Channel 7
Logic 1 written to any bit enables a group of channels and Logic 0 disables a group. LDAC is used to toggle between the two
registers.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5570BRSZ-REEL7 | IC DAC 16BIT SERIAL IN 16SSOP |
| AD5570BRSZ-REEL | IC DAC 16BIT SERIAL IN 16SSOP |
| AD7538AQ | IC DAC 14BIT W/BUFF 24-CDIP |
| VE-B52-MU | CONVERTER MOD DC/DC 15V 200W |
| AD7537JR | IC DAC 12BIT DUAL MULT 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5392BST-3 | 制造商:Analog Devices 功能描述:DAC 8CH RES-STRING 14BIT 52LQFP - Trays 制造商:Rochester Electronics LLC 功能描述:8-CHN 3V SINGLE SUPPLY 14-BIT VOUT I.C. - Bulk |
| AD5392BST-5 | 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 52-Pin LQFP 制造商:Analog Devices 功能描述:14BIT DAC 8CH 5V SMD 5392 LQFP52 |
| AD5392BST-5-REEL | 制造商:Analog Devices 功能描述:DAC 8-CH Resistor-String 14-bit 52-Pin LQFP T/R |
| AD5392BSTZ-3 | 功能描述:IC DAC 14BIT 8CHAN 3V 52LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD5392BSTZ-5 | 功能描述:IC DAC 14BIT 8CHAN 3V 52LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
發布緊急采購，3分鐘左右您將得到回復。