參數資料
型號： AD7612BCPZ-RL
廠商： Analog Devices Inc
文件頁數： 2/32頁
文件大?。?/td> 0K
描述： IC ADC 16BIT 750KSPS SAR 48LFCSP
標準包裝： 2,500
系列： PulSAR®
位數： 16
采樣率（每秒）： 750k
數據接口： 串行，并聯
轉換器數目： 1
功率耗散（最大）： 230mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
供應商設備封裝： 48-LFCSP-VQ（7x7）
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，雙極
配用： EVAL-AD7612CBZ-ND - BOARD EVALUATION FOR AD7612
AD7612
Data Sheet
Rev. A | Page 10 of 32
Pin No.
Mnemonic
Type1
Description
23
D10 or
DO
In parallel mode, this output is used as Bit 10 of the parallel port data output bus.
SYNC
Serial Data Frame Synchronization. In serial master mode (SER/PAR = high, EXT/INT= low), this output
is used as a digital output frame synchronization for use with the internal data clock.
When a read sequence is initiated and INVSYNC = low, SYNC is driven high and remains high while the
SDOUT output is valid.
When a read sequence is initiated and INVSYNC = high, SYNC is driven low and remains low while the
SDOUT output is valid.
24
D11 or
DO
In parallel mode, this output is used as Bit 11 of the parallel port data output bus.
RDERROR
Serial Data Read Error. In serial slave mode (SER/PAR = high, EXT/INT = high), this output is used as an
incomplete data read error flag. If a data read is started and not completed when the current
conversion is complete, the current data is lost and RDERROR is pulsed high.
25
D12 or
DI/O
In parallel mode, this output is used as Bit 12 of the parallel port data output bus.
HW/SW
Serial Configuration Hardware/Software Select. In serial mode, this input is used to configure
the AD7612 by hardware or software. See the Hardware Configuration section and Software
When HW/SW = low, the AD7612 is configured through software using the serial configuration register.
When HW/SW = high, the AD7612 is configured through dedicated hardware input pins.
26
D13 or
DI/O
In parallel mode, this output is used as Bit 13 of the parallel port data output bus.
SCIN
Serial Configuration Data Input. In serial software configuration mode (SER/PAR = high, HW/SW = low)
this input is used to serially write in, MSB first, the configuration data into the serial configuration
register. The data on this input is latched with SCCLK. See the Software Configuration section.
27
D14 or
DI/O
In parallel mode, this output is used as Bit 14 of the parallel port data output bus.
SCCLK
Serial Configuration Clock. In serial software configuration mode (SER/PAR = high, HW/SW = low) this
input is used to clock in the data on SCIN. The active edge where the data SCIN is updated depends on
the logic state of the INVSCLK pin. See the Software Configuration section.
28
D15 or
DI/O
In parallel mode, this output is used as Bit 15 of the parallel port data output bus.
SCCS
Serial Configuration Chip Select. In serial software configuration mode (SER/PAR = high, HW/SW = low)
this input enables the serial configuration port. See the Software Configuration section.
29
BUSY
DO
Busy Output. Transitions high when a conversion is started, and remains high until the conversion
is complete and the data is latched into the on-chip shift register. The falling edge of BUSY can be
used as a data ready clock signal. Note that in master read after convert mode (SER/PAR = high,
EXT/INT = low, RDC = low) the busy time changes according to Table 4.
30
TEN
Input Range Select. Used in conjunction with BIPOLAR per the following:
Input Range
BIPOLAR
TEN
0 V to 5 V
Low
0 V to 10 V
Low
High
±5 V
High
Low
±10 V
High
31
RD
DI
Read Data. When CS and RD are both low, the interface parallel or serial output bus is enabled.
32
CS
DI
Chip Select. When CS and RD are both low, the interface parallel or serial output bus is enabled. CS is
also used to gate the external clock in slave serial mode (not used for serial programmable port).
33
RESET
DI
Reset Input. When high, reset the AD7612. Current conversion, if any, is aborted. The falling edge of
RESET resets the data outputs to all zero’s (with OB/2C = high) and clears the configuration register.
See the Digital Interface section. If not used, this pin can be tied to OGND.
34
PD
Power-Down Input. When PD = high, power down the ADC. Power consumption is reduced and
conversions are inhibited after the current one is completed. The digital interface remains active
during power down.
35
CNVST
DI
Conversion Start. A falling edge on CNVST puts the internal sample-and-hold into the hold state and
initiates a conversion.
36
BIPOLAR
Input Range Select. See description for Pin 30.
相關PDF資料
PDF描述
MS27467E17A35PB CONN PLUG 55POS STRAIGHT W/PINS
LTC1480IS8#TR IC TXRX RS485 3.3V ULT LP 8SOIC
VE-B62-MW-F2 CONVERTER MOD DC/DC 15V 100W
VI-2TZ-MY CONVERTER MOD DC/DC 2V 20W
IDT72241L15PF8 IC FIFO 2048X18 SYNC 15NS 32QFP
相關代理商/技術參數
參數描述
AD7612BST 制造商:Analog Devices 功能描述:ADC 16BIT 750KSPS SAR 48-LQFP 制造商:Analog Devices 功能描述:ADC, 16BIT, 750KSPS, SAR, 48-LQFP
AD7612BSTZ 功能描述:IC ADC 16BIT 750KSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
AD7612BSTZ-RL 功能描述:IC ADC 16BIT 750KSPS SAR 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:PulSAR® 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD7616BSTZ 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1
AD7616BSTZ-RL 功能描述:16 Bit Analog to Digital Converter 16 Input 2 SAR 80-LQFP (14x14) 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:在售 位數:16 采樣率（每秒）:1M 輸入數:16 輸入類型:差分 數據接口:SPI，并聯，DSP 配置:MUX-S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:5V 電壓 - 電源，數字:2.3 V ~ 3.6 V 特性:同步采樣 工作溫度:-40°C ~ 125°C 封裝/外殼:80-LQFP 供應商器件封裝:80-LQFP（14x14） 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*