- 您現在的位置：買賣IC網 > PDF目錄1985 > AD7949BCPZRL7 (Analog Devices Inc)IC ADC 14BIT 250KSPS 8CH 20LFCSP PDF資料下載
參數資料
| 型號： | AD7949BCPZRL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 13/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 250KSPS 8CH 20LFCSP |
| 產品培訓模塊： | Power Line Monitoring |
| 產品變化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 標準包裝： | 1,500 |
| 系列： | PulSAR® |
| 位數： | 14 |
| 采樣率（每秒）： | 250k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 15.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 20-LFCSP-VQ |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7949
Data Sheet
Rev. D | Page 20 of 32
External Reference and Internal Buffer
For improved drift performance, an external reference can be
used with the internal buffer, as shown in Figure 31. The
external source is connected to REFIN, the input to the on-chip
unity gain buffer, and the output is produced on the REF pin.
An external reference can be used with the internal buffer with
or without the temperature sensor enabled. Refer to Table 9 for
register details. With the buffer enabled, the gain is unity and is
limited to an input/output of VDD = 0.2 V; however, the
maximum voltage allowable must be ≤(VDD 0.5 V).
The internal reference buffer is useful in multiconverter appli-
cations because a buffer is typically required in these applications.
In addition, a low power reference can be used because the
internal buffer provides the necessary performance to drive the
SAR architecture of the AD7949.
REF
GND
TEMP
AD7949
10F
100nF
REFIN
REF SOURCE
≤ (VDD – 0.5V)
0
73
51
-0
31
Figure 31. External Reference Using Internal Buffer
External Reference
In any of the six voltage reference schemes, an external reference
can be connected directly on the REF pin as shown in Figure 32
because the output impedance of REF is >5 kΩ. To reduce power
consumption, the reference and buffer should be powered down.
When using only the external reference (and optional reference
buffer as shown in Figure 35), the internal buffer is disabled.
Refer to Table 9 for register details. For improved drift perfor-
mance, an external reference such as the ADR43x or ADR44x is
recommended.
REF
GND
TEMP
10F
REFIN
REF SOURCE
0.5V < REF < (VDD + 0.3V)
NO CONNECTION
REQUIRED
AD7949
07
35
1-
03
2
Figure 32. External Reference
Note that the best SNR is achieved with a 5 V external reference
as the internal reference is limited to 4.096 V. The SNR
degradation is as follows:
5
096
.
4
log
20
LOSS
SNR
Reference Decoupling
Whether using an internal or external reference, the AD7949
voltage reference output/input, REF, has a dynamic input
impedance and should therefore be driven by a low impedance
source with efficient decoupling between the REF and GND
pins. This decoupling depends on the choice of the voltage
reference but usually consists of a low ESR capacitor connected
to REF and GND with minimum parasitic inductance. A 10 μF
(X5R, 1206 size) ceramic chip capacitor is appropriate when
using the internal reference, the ADR43x/ADR44x external
reference, or a low impedance buffer such as the AD8031 or
The placement of the reference decoupling capacitor is also impor-
tant to the performance of the AD7949, as explained in the
Layout section. Mount the decoupling capacitor on the same side
as the ADC at the REF pin with a thick PCB trace. The GND
should also be connected to the reference decoupling capacitor
with the shortest distance and to the analog ground plane with
several vias.
If desired, smaller reference decoupling capacitor values down
to 2.2 μF can be used with minimal impact on performance,
especially on DNL.
Regardless, there is no need for an additional lower value ceramic
decoupling capacitor (for example, 100 nF) between the REF
and GND pins.
For applications that use multiple AD7949 devices or other
PulSAR devices, it is more effective to use the internal reference
buffer to buffer the external reference voltage, thus reducing
SAR conversion crosstalk.
The voltage reference temperature coefficient (TC) directly
impacts full scale; therefore, in applications where full-scale
accuracy matters, care must be taken with the TC. For instance,
a ±10 ppm/°C TC of the reference changes full scale by ±1 LSB/°C.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7951BSTZRL | IC ADC 14BIT 1MSPS 48-LQFP |
| AD7952BCPZ | IC ADC 14BIT DIFF 1MSPS 48LFCSP |
| AD7980ARMZ | ADC 16BIT 1MSPS LP 10-MSOP |
| AD7982BCPZ-RL | IC ADC 18BIT 1MSPS PULSAR 10LFCS |
| AD7983BCPZ-RL7 | IC ADC 16BIT 1.33MSPS 10LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7949SCPZ-EP-R2 | 功能描述:14 Bit Analog to Digital Converter 8 Input 1 SAR 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:PulSAR? 包裝:剪切帶（CT） 零件狀態:有效 位數:14 采樣率（每秒）:256k 輸入數:8 輸入類型:差分，單端 數據接口:SPI，DSP 配置:MUX-ADC 無線電 - S/H:ADC:- A/D 轉換器數:1 架構:SAR 參考類型:外部， 內部 電壓 - 電源，模擬:2.3 V ~ 5.5 V 電壓 - 電源，數字:2.3 V ~ 5.5 V 特性:溫度傳感器 工作溫度:-55°C ~ 125°C 封裝/外殼:20-WFQFN 裸露焊盤，CSP 供應商器件封裝:20-LFCSP-WQ（4x4） 標準包裝:1 |
| AD7949SCPZ-EP-RL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 14-bit Serial 20-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:8 CH 250KSPS 14BIT ADC IC - Tape and Reel 制造商:Analog Devices 功能描述:IC ADC 14BIT 8CH 250KSPS 20LFCSP 制造商:Analog Devices 功能描述:Analog to Digital Converters - ADC 14-Bit 8CH 250 kSPS 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD795 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
| AD795_02 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
| AD795_09 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Low Noise Precision FET Op Amp |
發布緊急采購，3分鐘左右您將得到回復。