參數資料
型號： AD8139ARDZ-REEL7
廠商： Analog Devices Inc
文件頁數： 11/25頁
文件大小： 0K
描述： IC AMP DIFF R-R LN LDIST 8SOIC
標準包裝： 1,000
放大器類型： 差分
電路數： 1
輸出類型： 差分，滿擺幅
轉換速率： 800 V/µs
-3db帶寬： 410MHz
電流 - 輸入偏壓： 2.25µA
電壓 - 輸入偏移： 150µV
電流 - 電源： 24.5mA
電流 - 輸出 / 通道： 100mA
電壓 - 電源，單路/雙路(±)： 4.5 V ~ 12 V，±2.25 V ~ 6 V
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm Width）裸露焊盤
供應商設備封裝： 8-SOIC-EP
包裝： 帶卷 (TR)
AD8139
Rev. B | Page 18 of 24
THEORY OF OPERATION
The AD8139 is a high speed, low noise differential amplifier
fabricated on the Analog Devices second-generation eXtra Fast
Complementary Bipolar (XFCB) process. It is designed to
provide two closely balanced differential outputs in response to
either differential or single-ended input signals. Differential
gain is set by external resistors, similar to traditional voltage-
feedback operational amplifiers. The common-mode level of
the output voltage is set by a voltage at the VOCM pin and is
independent of the input common-mode voltage. The AD8139
has an H-bridge input stage for high slew rate, low noise, and
low distortion operation and rail-to-rail output stages that
provide maximum dynamic output range. This set of features
allows for convenient single-ended-to-differential conversion, a
common need to take advantage of modern high resolution
ADCs with differential inputs.
TYPICAL CONNECTION AND DEFINITION OF
TERMS
Figure 59 shows a typical connection for the AD8139, using
matched external RF/RG networks. The differential input
terminals of the AD8139, VAP and VAN, are used as summing
junctions. An external reference voltage applied to the VOCM
terminal sets the output common-mode voltage. The two
output terminals, VOP and VON, move in opposite directions in a
balanced fashion in response to an input signal.
+
–
VAP
VAN
VON
VOP
–
+
VO, dm
RL, dm
AD8139
CF
RF
RG
CF
RF
VIP
VOCM
VIN
04
67
9-
0
50
Figure 59. Typical Connection
The differential output voltage is defined as
VO, dm = VOP VON
(1)
Common-mode voltage is the average of two voltages. The
output common-mode voltage is defined as
2
ON
OP
cm
O,
V
+
=
(2)
Output Balance
Output balance is a measure of how well VOP and VON are
matched in amplitude and how precisely they are 180° out of
phase with each other. It is the internal common-mode feedback
loop that forces the signal component of the output common-mode
towards zero, resulting in the near perfectly balanced differential
outputs of identical amplitude and exactly 180° out of phase. The
output balance performance does not require tightly matched
external components, nor does it require that the feedback factors
of each loop be equal to each other. Low frequency output balance
is limited ultimately by the mismatch of an on-chip voltage divider,
which is trimmed for optimum performance.
Output balance is measured by placing a well-matched resistor
divider across the differential voltage outputs and comparing
the signal at the midpoint of the divider with the magnitude of
the differential output. By this definition, output balance is
equal to the magnitude of the change in output common-mode
voltage divided by the magnitude of the change in output
differential-mode voltage:
dm
O,
cm
O,
V
Balance
Output
Δ
=
(3)
The block diagram of the AD8139 in Figure 60 shows the
external differential feedback loop (RF/RG networks and the
differential input transconductance amplifier, GDIFF) and the
internal common-mode feedback loop (voltage divider across
VOP and VON and the common-mode input transconductance
amplifier, GCM). The differential negative feedback drives the
voltages at the summing junctions VAN and VAP to be essentially
equal to each other.
VAN = VAP
(4)
The common-mode feedback loop drives the output common-
mode voltage, sampled at the midpoint of the two 500 Ω resistors,
to equal the voltage set at the VOCM terminal. This ensures that
2
dm
O,
OCM
OP
V
+
=
(5)
and
2
dm
O,
OCM
ON
V
=
(6)
VOP
VOCM
GO
GDIFF
GO
GCM
10pF
500
VON
MIDSUPPLY
+
VAN
VIN
VIP
VAP
RG
RF
04
67
9-
0
51
Figure 60. Block Diagram
相關PDF資料
PDF描述
LTC6082IGN#TRPBF IC AMP R-R QUAD I/O 16-SSOP
FG450 FUSE INDUST 450A 550V BS IEC
170M4512 FUSE 400A 690V 1GN/50 AR UC
2-102699-8 CONN HEADER VERT 60POS PCB 30AU
2-102617-3 CONN HEADER R/A .100 50POS 15AU
相關代理商/技術參數
參數描述
AD8139AR-REEL 制造商:Analog Devices 功能描述:ULTRA LOW NOISE FULLY DIFFERENTIAL ADC DRIVER - Tape and Reel
AD8139CP 制造商:Analog Devices 功能描述:
AD813ACHIPS 制造商:AD 制造商全稱:Analog Devices 功能描述:Single Supply, Low Power Triple Video Amplifier
AD813AN 制造商:Analog Devices 功能描述:OP Amp Triple GP R-R O/P 制造商:Rochester Electronics LLC 功能描述:TRPL LO PWR I-FDBK OP AMP - Bulk 制造商:Analog Devices 功能描述:IC AMP TRIPLE VIDEO DIP14 813
AD813ANZ 功能描述:IC OPAMP TRIPLE VIDEO LP 14DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*