- 您現在的位置：買賣IC網 > PDF目錄11232 > AD8195ACPZ-R7 (Analog Devices Inc)IC BUFF HDMI/DVI W/EQUAL 40LFCSP PDF資料下載
參數資料
| 型號： | AD8195ACPZ-R7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大小： | 0K |
| 描述： | IC BUFF HDMI/DVI W/EQUAL 40LFCSP |
| 標準包裝： | 750 |
| 功能： | 開關 |
| 電路： | 1 x 1:1 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 40-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 40-LFCSP-VQ（6x6） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Data Sheet
AD8195
Rev. B | Page 15 of 20
APPLICATIONS INFORMATION
FRONT PANEL BUFFER FOR ADVANCED TV
A front panel input provides easy access to an HDMI connector
for connecting devices, such as an HD camcorder or video game
console, to an HDTV. In designs where the main PCB is not
near the side or front of the HDTV, a front panel HDMI input
must be connected to the main board through a cable. The
AD8195 enables the implementation of a front or side panel
HDMI input for an HDTV by buffering the HDMI signals and
compensating for the cable interconnect to the main board.
A simplified typical front panel buffer circuit is shown in Figure 33.
The AD8195 is designed to have an HDMI/DVI receiver pinout
at its input and a transmitter pinout at its output. This makes
the AD8195 ideal for use in television set front panel connectors
and AVR-type applications where a designer routes both the
inputs and the outputs directly to HDMI/DVI connectors.
One advantage of the AD8195 in a television set front panel
connector is that all of the high speed signals can be routed on
one side (the topside) of the board. The AD8195 provides 12 dB
of input equalization so it can compensate for the signal degra-
dation of long input cables. In addition, the AD8195 can also
provide up to 6 dB of output preemphasis that boosts the output
TMDS signals and allows the AD8195 to precompensate when
driving long PCB traces or high loss output cables. The net
effect of the input equalization and output preemphasis of the
degradation of both the input and output cables; it acts to reopen
a closed input data eye and transmit a full swing HDMI signal
to an end receiver.
Placement of a shunt resistor from the negative terminal of the
input TMDS clock differential pair to ground is recommended
to prevent amplification of ambient noise resulting in a large
swing signal at the input of the HDMI receiver.
For the CEC and DDC buffer circuits to be active when the
local supply is off, power must be provided to the AD8195
AMUXVCC supply pin from the HDMI source. The 5 V from
the HDMI connector and the local 5 V supply should be isolated
with diodes to prevent contention. Additionally, the diodes
should be selected such that the forward voltage drop from the
local supply is less than from the HDMI source so that current
is not drawn from the HDMI source when the local supply is on.
The rise time of the CEC buffer output is set by the time constant
of the pull-up resistance and the capacitance on the output node.
An additional external pull-up resistance is recommended at
the CEC output to allow for optimal rise times. A Thevenin
equivalent 2 kΩ pull-up to 3.3 V is shown in Figure 34.
The VREF_IN and VREF_OUT pins are voltage references for
the input and output pins of DDC buffer. The external pull-up
resistors for the DDC bus should be connected to the same
voltage as applied to the respective VREF pin.
Typically, an EDID EEPROM is placed prior to the AD8195,
as shown in Figure 34. If desired, the EDID EEPROM can be
downstream of the AD8195. This optional configuration is also
illustrated in Figure 34. Regardless of the configuration, the
pull-up voltage at the DDC output should be on even when the
local system power supply is off.
To ensure that the AD8195 operates properly, Pin 21 (COMP)
should be tied to ground through a 10 F bypass capacitor. A 34 kΩ
pull-up resistor from COMP to AMUXVCC is integrated on chip.
HDTV SET
HDMI RX
AD8195
MAIN PCB
CABLE
07049-
008
Figure 33. AD8195 as a Front Panel Buffer for an HDTV
相關PDF資料 |
PDF描述 |
|---|---|
| M39014/02-1310V | CAP CER 100000PF 10% 100V RAD |
| LT1205CS#TR | IC VIDEO MULTIPLEXER SPDT 16SOIC |
| ADG5212BCPZ-RL7 | IC SWITCH SPST QUAD 16LFCSP |
| ADG5213BCPZ-RL7 | IC SWITCH SPST QUAD 16LFCSP |
| ADG715BRU-REEL7 | IC SWITCH OCTAL SPST 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8195-EVALZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits) |
| AD8195XCPZ | 功能描述:IC BUFF HDMI/DVI W/EQUAL 40LFCSP 制造商:analog devices inc. 系列:- 包裝:托盤 零件狀態:上次購買時間 類型:HDMI/DVI 緩沖器 應用:HDTV 安裝類型:表面貼裝 封裝/外殼:40-VFQFN 裸露焊盤，CSP 供應商器件封裝:40-LFCSP-VQ（6x6） 標準包裝:1 |
| AD8196 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2:1 HDMI/DVI Switch with Equalization |
| AD8196ACPZ | 功能描述:IC SWITCH DVI/HDMI 2:1 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| AD8196ACPZ-R7 | 功能描述:IC SWITCH DVI/HDMI 2:1 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
發布緊急采購，3分鐘左右您將得到回復。