- 您現在的位置：買賣IC網 > PDF目錄17019 > AD9644-155KITZ (Analog Devices Inc)KIT EVAL FOR AD9644 PDF資料下載
參數資料
| 型號： | AD9644-155KITZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 32/44頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR AD9644 |
| 設計資源： | AD9644 Gerber Files |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9644
Data Sheet
Rev. C | Page 38 of 44
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
(Hex)
Default/
Comments
0x76
JESD204A
serial reserved
Field 1 (RES1)
Serial Reserved Field 1 (RES1) – these registers are available for customer use
0x00
0x77
JESD204A
serial reserved
Field 2 (RES2)
Serial Reserved Field 2 (RES2) – these registers are available for customer use
0x00
0x78
JESD204A
checksum
value (FCHK)
for Lane 0
(local)
Serial checksum value for Lane 0 (FCHK)
0x00
Read only
0x79
JESD204A
checksum
value (FCHK)
for lane 1
(local)
Serial checksum value for Lane 1 (FCHK)
0x00
Read only
1
The channel index register at Address 0x05 should be set to 0x03 (default) when writing to Address 0x00.
MEMORY MAP REGISTER DESCRIPTIONS
For additional information about functions controlled in
Register 0x00 to Register 0x25, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
Sync Control (Register 0x3A)
Bits[7:3]—Open
Bit 2—Clock Divider Next Sync Only
If the master sync buffer enable bit (Address 0x3A, Bit 0) and
the clock divider sync enable bit (Address 0x3A, Bit 1) are high, Bit
2 allows the clock divider to sync to the first sync pulse it receives
and to ignore the rest. The clock divider sync enable bit (Address
0x3A, Bit 1) resets after it syncs.
Bit 1—Clock Divider Sync Enable
Bit 1 gates the sync pulse to the clock divider. The sync signal is
enabled when Bit 1 is high and Bit 0 is high. This is continuous
sync mode.
Bit 0—Master Sync Buffer Enable
Bit 0 must be high to enable any of the sync functions. If the
sync capability is not used this bit should remain low to
conserve power.
JESD204A Quick Configure (Register 0x5E)
Bits[7:3]—Reserved
Bits[2:0]—Register Quick Configuration
Writes to Bits[2:0] of this register configure the part for the
most popular modes of operation for the JESD204A link. The
intent of this register is to simplify the part setup for typical
serial link operation modes. Writing values other than 0x0 to
this register causes registers throughout the JESD204A memory
map to be updated. Once these registers have been written the
affected JESD204A configuration register reads back with their
new values and can be updated. These bits are self clearing and
always read back as 0b000.
000: default—configuration determined by other registers
001: two converters using two links with one lane per link
(maximum sample rate = 80 MHz or 155 MHz) Each link
configuration:
M = 1; N’ = 16; CF = 0; K = 16; S = 1; F = 2; L = 1; HD = 0;
010 = two converters using one link with two lanes per link
(Maximum sample rate = 80 MHz or 155 MHz). Each link
configuration:
M = 2; N’ = 16; CF = 0; K = 16; S = 1; F = 2; L = 2; HD = 0;
uses DSYNCA pin for synchronization. Setting this mode sets
Address 0x5F = 0x02 and sets Address 0x60 = 0x14 for Link A
and sets Address 0x60 = 0x01 for Link B.
011 = two converters using one link and a single lane (maxi-
mum sample rate = 78.125 MHz). Each link configuration: M = 2;
N’ = 16; CF = 0; K = 8;S = 1; F = 4; L = 1; HD = 0; uses DSYNCA
pin for synchronization and DOUTA for output signals.
100 to 111: reserved.
JESD204A Lane Assignment (Register 0x5F)
Bits[7:4]—Reserved
Bits[3:0]—JESD204A Serial Lane Control
These bits set the lane usage. See Figure 62.
0000: one lane per link. Link A: Lane 0 sent on Lane A,
Link B: Lane 0 sent on Lane B.
0001: one lane per link. Link A: Lane 0 sent on Lane B,
Link B: Lane 0 sent on Lane A.
0010: two lanes per link. Link A: Lane 0, one sent on Lane A,
Link B disabled.
0011: two lanes per link. Link A: Lane 0, one sent on Lane B,
Lane A. Link B disabled.
0100: two lanes per link. Link B: Lane 0, one sent on Lane A,
Lane B. Link A disabled.
0101: two lanes per link. Link B: Lane 0, one sent on Lane B,
Lane A. Link A disabled.
0110 to 1111: reserved for future use.
相關PDF資料 |
PDF描述 |
|---|---|
| 0210490367 | CABLE JUMPER 1.25MM .051M 30POS |
| DS9097U-009# | COM PORT ADAPTER |
| HKQ0603S3N6C-T | INDUCTOR HI FREQ 3.6NH 0201 |
| VI-2WX-EY | CONVERTER MOD DC/DC 5.2V 50W |
| AD9641-155KITZ | KIT EVAL FOR AD9641 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9644-80KITZ | 功能描述:BOARD EVALUATION FOR AD9644 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| AD9644BCPZ-155 | 功能描述:模數轉換器 - ADC 14 Bit 155 Msps Dual 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9644BCPZ-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9644BCPZRL7-155 | 功能描述:模數轉換器 - ADC 14 Bit 155 Msps Dual 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9644BCPZRL7-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。