參數資料
型號： AD9644-80KITZ
廠商： Analog Devices Inc
文件頁數： 32/44頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD9644
設計資源： AD9644 Gerber Files
AD9644 80KITZ BOM
標準包裝： 1
ADC 的數量： 2
位數： 14
采樣率（每秒）： 80M
數據接口： 串行
輸入范圍： 1.4 ~ 2.1 Vpp
在以下條件下的電源（標準）： *
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD9644
已供物品： 板
AD9644
Data Sheet
Rev. C | Page 38 of 44
Addr
(Hex)
Register
Name
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
(Hex)
Default/
Comments
0x76
JESD204A
serial reserved
Field 1 (RES1)
Serial Reserved Field 1 (RES1) – these registers are available for customer use
0x00
0x77
JESD204A
serial reserved
Field 2 (RES2)
Serial Reserved Field 2 (RES2) – these registers are available for customer use
0x00
0x78
JESD204A
checksum
value (FCHK)
for Lane 0
(local)
Serial checksum value for Lane 0 (FCHK)
0x00
Read only
0x79
JESD204A
checksum
value (FCHK)
for lane 1
(local)
Serial checksum value for Lane 1 (FCHK)
0x00
Read only
1
The channel index register at Address 0x05 should be set to 0x03 (default) when writing to Address 0x00.
MEMORY MAP REGISTER DESCRIPTIONS
For additional information about functions controlled in
Register 0x00 to Register 0x25, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
Sync Control (Register 0x3A)
Bits[7:3]—Open
Bit 2—Clock Divider Next Sync Only
If the master sync buffer enable bit (Address 0x3A, Bit 0) and
the clock divider sync enable bit (Address 0x3A, Bit 1) are high, Bit
2 allows the clock divider to sync to the first sync pulse it receives
and to ignore the rest. The clock divider sync enable bit (Address
0x3A, Bit 1) resets after it syncs.
Bit 1—Clock Divider Sync Enable
Bit 1 gates the sync pulse to the clock divider. The sync signal is
enabled when Bit 1 is high and Bit 0 is high. This is continuous
sync mode.
Bit 0—Master Sync Buffer Enable
Bit 0 must be high to enable any of the sync functions. If the
sync capability is not used this bit should remain low to
conserve power.
JESD204A Quick Configure (Register 0x5E)
Bits[7:3]—Reserved
Bits[2:0]—Register Quick Configuration
Writes to Bits[2:0] of this register configure the part for the
most popular modes of operation for the JESD204A link. The
intent of this register is to simplify the part setup for typical
serial link operation modes. Writing values other than 0x0 to
this register causes registers throughout the JESD204A memory
map to be updated. Once these registers have been written the
affected JESD204A configuration register reads back with their
new values and can be updated. These bits are self clearing and
always read back as 0b000.
000: default—configuration determined by other registers
001: two converters using two links with one lane per link
(maximum sample rate = 80 MHz or 155 MHz) Each link
configuration:
M = 1; N’ = 16; CF = 0; K = 16; S = 1; F = 2; L = 1; HD = 0;
010 = two converters using one link with two lanes per link
(Maximum sample rate = 80 MHz or 155 MHz). Each link
configuration:
M = 2; N’ = 16; CF = 0; K = 16; S = 1; F = 2; L = 2; HD = 0;
uses DSYNCA pin for synchronization. Setting this mode sets
Address 0x5F = 0x02 and sets Address 0x60 = 0x14 for Link A
and sets Address 0x60 = 0x01 for Link B.
011 = two converters using one link and a single lane (maxi-
mum sample rate = 78.125 MHz). Each link configuration: M = 2;
N’ = 16; CF = 0; K = 8;S = 1; F = 4; L = 1; HD = 0; uses DSYNCA
pin for synchronization and DOUTA for output signals.
100 to 111: reserved.
JESD204A Lane Assignment (Register 0x5F)
Bits[7:4]—Reserved
Bits[3:0]—JESD204A Serial Lane Control
These bits set the lane usage. See Figure 62.
0000: one lane per link. Link A: Lane 0 sent on Lane A,
Link B: Lane 0 sent on Lane B.
0001: one lane per link. Link A: Lane 0 sent on Lane B,
Link B: Lane 0 sent on Lane A.
0010: two lanes per link. Link A: Lane 0, one sent on Lane A,
Link B disabled.
0011: two lanes per link. Link A: Lane 0, one sent on Lane B,
Lane A. Link B disabled.
0100: two lanes per link. Link B: Lane 0, one sent on Lane A,
Lane B. Link A disabled.
0101: two lanes per link. Link B: Lane 0, one sent on Lane B,
Lane A. Link A disabled.
0110 to 1111: reserved for future use.
相關PDF資料
PDF描述
0210490968 CABLE JUMPER 1.25MM .076M 27POS
VI-2WZ-EX CONVERTER MOD DC/DC 2V 30W
VI-2WZ-EW CONVERTER MOD DC/DC 2V 40W
0210490368 CABLE JUMPER 1.25MM .051M 30POS
VI-2WY-EY CONVERTER MOD DC/DC 3.3V 33W
相關代理商/技術參數
參數描述
AD9644BCPZ-155 功能描述:模數轉換器 - ADC 14 Bit 155 Msps Dual 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9644BCPZ-80 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9644BCPZRL7-155 功能描述:模數轉換器 - ADC 14 Bit 155 Msps Dual 1.8V ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體:
AD9644BCPZRL7-80 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
AD9644CCPZ-80 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*