- 您現在的位置：買賣IC網 > PDF目錄16521 > AD9859/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9859 PDF資料下載
參數資料
| 型號： | AD9859/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/24頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9859 |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | AD9859 Eval Brd BOM AD9859, AD9951-54 Eval Brd Gerber Files |
| 標準包裝： | 1 |
| 系列： | AgileRF™ |
| 主要目的： | 計時，直接數字合成（DDS） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9859 |
| 主要屬性： | 10 位數模轉換器，32 位調節字寬 |
| 次要屬性： | 400MHz 圖形用戶界面 |
| 已供物品： | 板，軟件 |
AD9859
Rev. A | Page 7 of 24
PIN FUNCTION DESCRIPTIONS
Table 3. Pin Function Descriptions—48-Lead TQFP/EP
Pin No.
Mnemonic
I/O
Description
1
I/O UPDATE
I
The rising edge transfers the contents of the internal buffer memory to the I/O registers. This
pin must be set up and held around the SYNC_CLK output signal.
2, 34
DVDD
I
Digital Power Supply Pins (1.8 V).
3, 33, 42, 47,
48
DGND
I
Digital Power Ground Pins.
4, 6, 13, 16, 18,
19, 25, 27, 29
AVDD
I
Analog Power Supply Pins (1.8 V).
5, 7, 14, 15, 17,
22, 26, 28, 30,
31, 32
AGND
I
Analog Power Ground Pins.
8
OSC/
I
REFCLK
Complementary Reference Clock/Oscillator Input. When the REFCLK port is operated in single-
ended mode, REFCLKB should be decoupled to AVDD with a 0.1 F capacitor.
9
OSC/REFCLK
I
Reference Clock/Oscillator Input. See the Clock Input section for details on the
OSCILLATOR/REFCLK operation.
10
CRYSTAL OUT
O
Output of the Oscillator Section.
11
CLKMODESELECT
I
Control Pin for the Oscillator Section. When high, the oscillator section is enabled. When low,
the oscillator section is bypassed.
12
LOOP_FILTER
I
This pin provides the connection for the external zero compensation network of the REFCLK
multiplier’s PLL loop filter. The network consists of a 1 k resistor in series with a 0.1 F
capacitor tied to AVDD.
20
IOUT
O
Complementary DAC Output. Should be biased through a resistor to AVDD, not AGND.
21
IOUT
O
DAC Output. Should be biased through a resistor to AVDD, not AGND.
23
DACBP
I
DAC Band Gap Decoupling Pin. A 0.1 μF capacitor to AGND is recommended.
24
DAC_R
SET
I
A resistor (3.92 k nominal) connected from AGND to DAC_R
SET establishes the reference
current for the DAC.
35
PWRDWNCTL
I
Input Pin Used as an External Power-Down Control (see Table 8 for details).
36
RESET
I
Active High Hardware Reset Pin. Asserting the RESET pin forces the AD9859 to the initial state,
as described in the I/O port register map.
37
IOSYNC
I
Asynchronous Active High Reset of the Serial Port Controller. When high, the current I/O
operation is immediately terminated, enabling a new I/O operation to commence once IOSYNC
is returned low. If unused, ground this pin; do not allow this pin to float.
38
SDO
O
When operating the I/O port as a 3-wire serial port, this pin serves as the serial data output.
When operated as a 2-wire serial port, this pin is unused and can be left unconnected.
39
CS
I
This pin functions as an active low chip select that allows multiple devices to share the I/O bus.
40
SCLK
I
This pin functions as the serial data clock for I/O operations.
41
SDIO
I/O
When operating the I/O port as a 3-wire serial port, this pin serves as the serial data input only.
When operated as a 2-wire serial port, this pin is the bidirectional serial data pin.
43
DVDD_I/O
I
Digital Power Supply (for I/O Cells Only, 3.3 V).
44
SYNC_IN
I
Input Signal Used to Synchronize Multiple AD9859s. This input is connected to the SYNC_CLK
output of a master AD9859.
45
SYNC_CLK
O
Clock Output Pin Serves as a Synchronizer for External Hardware.
46
OSK
I
Input Pin Used to Control the Direction of the Shaped On-Off Keying Function when
Programmed for Operation. OSK is synchronous to the SYNC_CLK pin. When OSK is not
programmed, this pin should be tied to DGND.
<49>
AGND
I
The exposed paddle on the bottom of the package is a ground connection for the DAC and
must be attached to AGND in any board layout.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J0X-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
| 2-5349573-0 | FOMM62.5 LEAD 2.5S ST/PC-ST/PC |
| HCM15DSEN-S243 | CONN EDGECARD 30POS .156 EYELET |
| AD9547/PCBZ | BOARD EVALUATION FOR AD9547 |
| UPA1E331MPD1TD | CAP ALUM 330UF 25V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9859YSV | 制造商:Analog Devices 功能描述:Direct Digital Synthesizer 400MHz 1-DAC 10-Bit Serial 48-Pin TQFP EP 制造商:Analog Devices 功能描述:DDS 10BIT DAC 400MSPS SMD 9859 |
| AD9859YSV-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| AD9859YSVZ | 功能描述:IC DDS DAC 10BIT 400MSPS 48-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9859YSVZ | 制造商:Analog Devices 功能描述:IC 400 MSPS DDS 制造商:Analog Devices 功能描述:IC, 400 MSPS DDS |
| AD9859YSVZ | 制造商:Analog Devices 功能描述:DIRECT DIGITAL SYNTHESIZER |
發布緊急采購，3分鐘左右您將得到回復。