- 您現在的位置：買賣IC網 > PDF目錄16521 > AD9859/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9859 PDF資料下載
參數資料
| 型號： | AD9859/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9859 |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | AD9859 Eval Brd BOM AD9859, AD9951-54 Eval Brd Gerber Files |
| 標準包裝： | 1 |
| 系列： | AgileRF™ |
| 主要目的： | 計時，直接數字合成（DDS） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9859 |
| 主要屬性： | 10 位數模轉換器，32 位調節字寬 |
| 次要屬性： | 400MHz 圖形用戶界面 |
| 已供物品： | 板，軟件 |
AD9859
Rev. A | Page 15 of 24
CFR1<6>: Not Used
CFR1<5>: DAC Power-Down Bit
CFR1<5> = 0 (default). The DAC is enabled for operation.
CFR1<5> = 1. The DAC is disabled and is in its lowest power
dissipation state.
CFR1<4>: Clock Input Power-Down Bit
CFR1<4> = 0 (default). The clock input circuitry is enabled for
operation.
CFR1<4> = 1. The clock input circuitry is disabled, and the
device is in its lowest power dissipation state.
CFR1<3>: External Power-Down Mode
CFR1<3> = 0 (default). The external power-down mode
selected is the rapid recovery power-down mode. In this mode,
when the PWRDWNCTL input pin is high, the digital logic
and the DAC digital logic are powered down. The DAC bias
circuitry, PLL, oscillator, and clock input circuitry are not
powered down.
CFR1<3> = 1. The external power-down mode selected is the
full power-down mode. In this mode, when the PWRDWNCTL
input pin is high, all functions are powered down. This includes
the DAC and PLL, which take a significant amount of time to
power up.
CFR1<2>: Not Used
CFR1<1>: SYNC_CLK Disable Bit
CFR1<1> = 0 (default). The SYNC_CLK pin is active.
CFR1<1> = 1. The SYNC_CLK pin assumes a static Logic 0
state to keep noise generated by the digital circuitry at a
minimum. However, the synchronization circuitry remains
active (internally) to maintain normal device timing.
CFR1<0>: Not Used, Leave at 0
Control Function Register No. 2 (CFR2)
The CFR2 is used to control the various functions, features, and
modes of the AD9859, primarily related to the analog sections
of the chip.
CFR2<23:12>: Not Used
CFR2<11>: High Speed Sync Enable Bit
CFR2<11> = 0 (default). The high speed sync enhancement is off.
CFR2<11> = 1. The high speed sync enhancement is on. This
bit should be set when attempting to use the auto-synchronization
feature for SYNC_CLK inputs beyond 50 MHz, (200 MSPS
SYSCLK). See the Synchronizing Multiple AD9859s section
for details.
CFR2<10>: Hardware Manual Sync Enable Bit
CFR2<10> = 0 (default). The hardware manual sync function is off.
CFR2<10> = 1. The hardware manual sync function is enabled.
While this bit is set, a rising edge on the SYNC_IN pin causes
the device to advance the SYNC_CLK rising edge by one REFCLK
cycle. Unlike the software manual sync enable bit, this bit does
not self-clear. Once the hardware manual sync mode is enabled,
it stays enabled until this bit is cleared. See the Synchronizing
Multiple AD9859s section for details.
CFR2<9>: CRYSTAL OUT Enable Bit
CFR2<9> = 0 (default). The CRYSTAL OUT pin is inactive.
CFR2<9> = 1. The CRYSTAL OUT pin is active. When active,
the crystal oscillator circuitry output drives the CRYSTAL OUT
pin, which can be connected to other devices to produce a
reference frequency. The oscillator responds to crystals in the
range of 20 MHz to 30 MHz.
CFR2<8>: Not Used
CFR2<7:3>: Reference Clock Multiplier Control Bits
This 5-bit word controls the multiplier value out of the clock-
multiplier (PLL) block. Valid values are decimal 4 to 20 (0x04 to
0x14). Values entered outside this range bypass the clock
multiplier. See the Phase-Locked Loop (PLL) section for details.
CFR2<2>: VCO Range Control Bit
This bit is used to control the range setting on the VCO.
When CFR2<2> == 0 (default), the VCO operates in a range of
100 MHz to 250 MHz. When CFR2<2> == 1, the VCO operates
in a range of 250 MHz to 400 MHz.
CFR2<1:0>: Charge Pump Current Control Bits
These bits are used to control the current setting on the charge
pump. The default setting, CFR2<1:0>, sets the charge pump
current to the default value of 75 A. For each bit added (01, 10,
11), 25 A of current is added to the charge pump current:
100 A, 125 A, and 150 A.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J0X-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
| 2-5349573-0 | FOMM62.5 LEAD 2.5S ST/PC-ST/PC |
| HCM15DSEN-S243 | CONN EDGECARD 30POS .156 EYELET |
| AD9547/PCBZ | BOARD EVALUATION FOR AD9547 |
| UPA1E331MPD1TD | CAP ALUM 330UF 25V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9859YSV | 制造商:Analog Devices 功能描述:Direct Digital Synthesizer 400MHz 1-DAC 10-Bit Serial 48-Pin TQFP EP 制造商:Analog Devices 功能描述:DDS 10BIT DAC 400MSPS SMD 9859 |
| AD9859YSV-REEL7 | 制造商:AD 制造商全稱:Analog Devices 功能描述:400 MSPS, 10-Bit, 1.8 V CMOS Direct Digital Synthesizer |
| AD9859YSVZ | 功能描述:IC DDS DAC 10BIT 400MSPS 48-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9859YSVZ | 制造商:Analog Devices 功能描述:IC 400 MSPS DDS 制造商:Analog Devices 功能描述:IC, 400 MSPS DDS |
| AD9859YSVZ | 制造商:Analog Devices 功能描述:DIRECT DIGITAL SYNTHESIZER |
發布緊急采購，3分鐘左右您將得到回復。