參數資料
型號： ADSP-21061LKB-160
廠商： Analog Devices Inc
文件頁數： 4/52頁
文件大小： 0K
描述： IC DSP CONTROLLER 32BIT 225BGA
產品培訓模塊： SHARC Processor Overview
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： 同步串行端口（SSP）
時鐘速率： 40MHz
非易失內存： 外部
芯片上RAM： 128kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 3.30V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 225-BBGA
供應商設備封裝： 225-PBGA
包裝： 托盤
Rev. D | Page 12 of 52 | May 2013
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1 JTAG
test access port of the ADSP-2106x to monitor and control the
target board processor during emulation. The EZ-ICE probe
requires the ADSP-2106x’s CLKIN, TMS, TCK, TDI, TDO, and
GND signals be made accessible on the target system via a
14-pin connector (a 2-row, 7-pin strip header) such as that
shown in Figure 5. The EZ-ICE probe plugs directly onto this
connector for chip-on-board emulation. You must add this con-
nector to your target board design if you intend to use the
ADSP-2106x EZ-ICE. The total trace length between the EZ-
ICE connector and the farthest device sharing the EZ-ICE JTAG
pin should be limited to 15 inches maximum for guaranteed
operation. This length restriction must include EZ-ICE JTAG
signals that are routed to one or more ADSP-2106x devices, or a
combination of ADSP-2106x devices and other JTAG devices
on the chain.
The 14-pin, 2-row pin strip header is keyed at the Pin 3 loca-
tion—Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inches in length. Pin spacing
should be 0.1 0.1 inches. Pin strip headers are available from
vendors such as 3M, McKenzie, and Samtec. The BTMS, BTCK,
BTRST, and BTDI signals are provided so that the test access
port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins as shown in
Figure 5. If you are not going to use the test access port for
board testing, tie BTRST to GND and tie or pull up BTCK to
VDD. The TRST pin must be asserted (pulsed low) after power-
up (through BTRST on the connector) or held low for proper
operation of the ADSP-2106x. None of the Bxxx pins (Pins 5, 7,
9, and 11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as shown
Figure 6 shows JTAG scan path connections for systems that
contain multiple ADSP-2106x processors.
Connecting CLKIN to Pin 4 of the EZ-ICE header is optional.
The emulator only uses CLKIN when directed to perform oper-
ations such as starting, stopping, and single-stepping multiple
ADSP-2106xs in a synchronous manner. If you do not need
these operations to occur synchronously on the multiple proces-
sors, simply tie Pin 4 of the EZ-ICE header to ground.
If synchronous multiprocessor operations are needed and
CLKIN is connected, clock skew between the multiple
ADSP-21061 processors and the CLKIN pin on the EZ-ICE
header must be minimal. If the skew is too large, synchronous
operations may be off by one or more cycles between proces-
sors. For synchronous multiprocessor operation TCK, TMS,
CLKIN, and EMU should be treated as critical signals in terms
of skew, and should be laid out as short as possible on your
board. If TCK, TMS, and CLKIN are driving a large number of
ADSP-21061s (more than eight) in your system, then treat them
as a “clock tree” using multiple drivers to minimize skew. (See
Figure 7 below and “JTAG Clock Tree” and “Clock Distribu-
tion” in the “High Frequency Design Considerations” section of
the ADSP-2106x SHARC User’s Manual.)
If synchronous multiprocessor operations are not needed (i.e.,
CLKIN is not connected), just use appropriate parallel termina-
tion on TCK and TMS. TDI, TDO, EMU, and TRST are not
critical signals in terms of skew.
Figure 5. Target Board Connector For ADSP-2106x EZ-ICE Emulator
(Jumpers in Place)
TOP VIEW
13
14
11
12
910
9
7
8
56
3
4
12
EMU
GND
TMS
TCK
TRST
TDI
TDO
GND
KEY (NO PIN)
BTMS
BTCK
BTRST
BTDI
GND
Table 3. Core Instruction Rate/CLKIN Ratio Selection
Signal
Termination
TMS
Driven Through 22 Resistor (16 mA Driver)
TCK
Driven at 10 MHz Through 22 Resistor (16 mA
Driver)
TRST1
1 TRST is driven low until the EZ-ICE probe is turned on by the emulator at software
startup. After software startup, is driven high.
Active Low Driven Through 22 Resistor (16 mA
Driver) (Pulled Up by On-Chip 20 k Resistor)
TDI
Driven by 22 Resistor (16 mA Driver)
TDO
One TTL Load, Split Termination (160/220)
CLKIN
One TTL Load, Split Termination (160/220)
EMU
Active Low, 4.7 k Pull-Up Resistor, One TTL Load
(Open-Drain Output from the DSP)
相關PDF資料
PDF描述
GBM10DTKT-S288 CONN EDGECARD 20POS .156 EXTEND
HWS300-5 PWR SUP IND 5V 60A SNG OUTPUT
VI-B2Y-CX-F4 CONVERTER MOD DC/DC 3.3V 49.5W
VI-B2Y-CX-F1 CONVERTER MOD DC/DC 3.3V 49.5W
TAJY107M016RNJ CAP TANT 100UF 16V 20% 2917
相關代理商/技術參數
參數描述
ADSP-21061LKB-176 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer Family
ADSP-21061LKBZ-160 功能描述:IC DSP CONTROLLER 32BIT 225-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP21061LKS160 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 40MHz 40MIPS 240-Pin MQFP Tray
ADSP-21061LKS-160 制造商:Rochester Electronics LLC 功能描述:ADSP-21061 1MBIT,40MHZ, 3V SHARC - Bulk 制造商:Analog Devices 功能描述:IC SHARC DSP 40MHZ 21061 MQFP240
ADSP-21061LKS-176 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 44MHz 44MIPS 240-Pin MQFP Tray 制造商:Rochester Electronics LLC 功能描述:ADSP-21061L 44HZ, 3V SHARC - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*