參數資料
型號： ADSP-2185NKCAZ-320
廠商： Analog Devices Inc
文件頁數： 4/48頁
文件大?。?/td> 0K
描述： IC DSP 16BIT 80MHZ 144CSPBGA
標準包裝： 1
系列： ADSP-21xx
類型： 定點
接口： 主機接口，串行端口
時鐘速率： 80MHz
非易失內存： 外部
芯片上RAM： 80kB
電壓 - 輸入/輸出： 1.8V，2.5V，3.3V
電壓 - 核心： 1.80V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 144-LFBGA，CSPBGA
供應商設備封裝： 144-CSBGA（10x10）
包裝： 托盤
Rev. A
|
Page 12 of 48
|
August 2006
ADSP-218xN
IOWAIT0–3 as shown in Figure 10, which in combination with
the wait state mode bit, specify up to 15 wait states to be auto-
matically generated for each of four regions. The wait states act
on address ranges, as shown in Table 6.
Note
: In Full Memory Mode, all 2048 locations of I/O space are
directly addressable. In Host Memory Mode, only address pin
A0 is available; therefore, additional logic is required externally
to achieve complete addressability of the 2048 I/O
space locations.
Composite Memory Select
ADSP-218xN series members have a programmable memory
select signal that is useful for generating memory select signals
for memories mapped to more than one space. The CMS signal
is generated to have the same timing as each of the individual
memory select signals (PMS, DMS, BMS, IOMS) but can com-
bine their functionality. Each bit in the CMSSEL register, when
set, causes the CMS signal to be asserted when the selected
memory select is asserted. For example, to use a 32K word
memory to act as both program and data memory, set the PMS
and DMS bits in the CMSSEL register and use the CMS pin to
drive the chip select of the memory, and use either DMS or PMS
as the additional address bit.
The CMS pin functions like the other memory select signals
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at
reset, except the BMS bit.
See Figure 11 and Figure 12 for illustration of the programma-
ble flag and composite control register and the system
control register.
Byte Memory Select
The ADSP-218xN’s BMS disable feature combined with the
CMS pin allows use of multiple memories in the byte memory
space. For example, an EPROM could be attached to the BMS
select, and a flash memory could be connected to CMS. Because
at reset BMS is enabled, the EPROM would be used for booting.
After booting, software could disable BMS and set the CMS sig-
nal to respond to BMS, enabling the flash memory.
Byte Memory
The byte memory space is a bidirectional, 8-bit-wide,
external memory space used to store programs and data. Byte
memory is accessed using the BDMA feature. The byte memory
space consists of 256 pages, each of which is 16K
8bits.
The byte memory space on the ADSP-218xN series supports
read and write operations as well as four different data formats.
The byte memory uses data bits 15–8 for data. The byte mem-
ory uses data bits 23–16 and address bits 13–0 to create a 22-bit
address. This allows up to a 4 megabit
8 (32 megabit) ROM
or RAM to be used without glue logic. All byte memory accesses
are timed by the BMWAIT register and the wait state mode bit.
Byte Memory DMA (BDMA, Full Memory Mode)
The byte memory DMA controller (Figure 13) allows loading
and storing of program instructions and data using the byte
memory space. The BDMA circuit is able to access the byte
memory space while the processor is operating normally and
steals only one DSP cycle per 8-, 16-, or 24-bit word transferred.
Table 6. Wait States
Address Range
Wait State Register
0x000–0x1FF
IOWAIT0 and Wait State Mode Select Bit
0x200–0x3FF
IOWAIT1 and Wait State Mode Select Bit
0x400–0x5FF
IOWAIT2 and Wait State Mode Select Bit
0x600–0x7FF
IOWAIT3 and Wait State Mode Select Bit
Figure 10. Wait State Control Register
In
ser
t W
ait
St
ate
Con
tro
l R
eg
ist
er
DWAIT
IOWAIT3
IOWAIT2
IOWAIT1
IOWAIT0
DM(0x3FFE)
WAIT STATE CONTROL
11
1
11
1
11
1 5 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
WAIT STATE MODE SELECT
0 = NORMAL MODE (PWAIT, DWAIT, IOWAIT0–3 = N WAIT STATES,
RANGING FROM 0 TO 7)
1 = 2N + 1 MODE (PWAIT, DWAIT, IOWAIT0–3 = 2N + 1 WAIT STATES,
RANGING FROM 0 TO 15)
Figure 11. Programmable Flag and Composite Control Register
Figure 12. System Control Register
BMW AIT
CM S S EL
0=D IS A BLE
CMS
1=E N AB LE
CMS
DM(0x3FE6)
PF TYPE
0= I N PUT
1= O U TP UT
( WH ER E B IT : 11 - IOM , 1 0 -B M, 9-DM , 8-P M )
1
0
1
00
0
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
PROGRAMMABLE FLAG AND COMPOSITE
SELECT CONTROL
RESERVED,ALW AY S
SE T TO 0
SP O RT0 E NABL E
0 = DIS ABL E
1= E NABL E
DM (0x3F FF)
S YSTEM CONTROL
S P ORT 1 E NABLE
0 = DIS ABLE
1 = ENABLE
S PO RT1 C ONF IGURE
0= FI,FO ,
IRQ0, IRQ1,SCLK
1= SPO RT1
DISABLE
BMS
0 = E NABL E
BMS
1= DIS AB LE
BMS
PWAIT
PROGRAM MEMOR Y
W AIT ST ATES
0
00
01
00
0
1
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
N OTE : RESERVED BITS ARE SHO WN O N A G RAY FIELD . THESE B ITS
SHOUL D ALW AYS BE WR ITTE N W ITH Z EROS .
RES ERV ED
SE T T O 0
相關PDF資料
PDF描述
LSM2-T/16-W3-C CONV DC/DC 52.8W 16A 5V SMD
GCM18DCSS CONN EDGECARD 36POS DIP .156 SLD
TAJF157K010RNJ CAP TANT 150UF 10V 10% 2312
GCM18DCMS CONN EDGECARD 36POS .156 WW
ADSP-BF526KBCZ-4 IC DSP CTRLR 400MHZ 289CSPBGA
相關代理商/技術參數
參數描述
ADSP-2185NKST-320 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 80MHz 80MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16K PM/16K DM RAM,16-BIT, 80 MIPS, 1.8V - Bulk 制造商:Analog Devices 功能描述:Digital Signal Processor IC Supply Volta
ADSP-2185NKSTZ-320 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-2185NKSTZ-3202 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP2186 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-2186 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*