- 您現在的位置：買賣IC網 > PDF目錄19370 > ADSP-TS201SABP-050 (Analog Devices Inc)IC PROCESSOR 500MHZ 576BGA PDF資料下載
參數資料
| 型號： | ADSP-TS201SABP-050 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROCESSOR 500MHZ 576BGA |
| 標準包裝： | 1 |
| 系列： | TigerSHARC® |
| 類型： | 定點/浮點 |
| 接口： | 主機接口，連接端口，多處理器 |
| 時鐘速率： | 500MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 3MB |
| 電壓 - 輸入/輸出： | 2.50V |
| 電壓 - 核心： | 1.05V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 576-BBGA 裸露焊盤 |
| 供應商設備封裝： | 576-BGA-ED（25x25） |
| 包裝： | 托盤 |
| 配用： | ADZS-TS201S-EZLITE-ND - KIT LITE EVAL FOR ADSP-TS201S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Rev. C
|
Page 16 of 48
|
December 2006
ADSP-TS201S
Table 8. Pin Definitions—External Port SDRAM Controller
Signal
Type
Term
Description
MSSD3–0
I/O/T
(pu_0)
nc
Memory Select SDRAM. MSSD0, MSSD1, MSSD2, or MSSD3 is asserted whenever the
DSP accesses SDRAM memory space. MSSD3–0 are decoded memory address pins
that are asserted whenever the DSP issues an SDRAM command cycle (access to
ADDR31:30 = 0b01—except reserved spaces shown in Figure 3 on Page 6). In a multi-
processor system, the master DSP drives MSSD3–0.
RAS
I/O/T
(pu_0)
nc
Row Address Select. When sampled low, RAS indicates that a row address is valid in
a read or write of SDRAM. In other SDRAM accesses, it defines the type of operation
to execute according to SDRAM specification.
CAS
I/O/T
(pu_0)
nc
Column Address Select. When sampled low, CAS indicates that a column address is
valid in a read or write of SDRAM. In other SDRAM accesses, it defines the type of
operation to execute according to the SDRAM specification.
LDQM
O/T
(pu_0)
nc
Low Word SDRAM Data Mask. When sampled high, three-states the SDRAM DQ
buffers. LDQM is valid on SDRAM transactions when CAS is asserted, and inactive on
read transactions. On write transactions, LDQM is active when accessing an odd
address word on a 64-bit memory bus to disable the write of the low word.
HDQM
O/T
(pu_0)
nc
High Word SDRAM Data Mask. When sampled high, three-states the SDRAM DQ
buffers. HDQM is valid on SDRAM transactions when CAS is asserted, and inactive on
read transactions. On write transactions, HDQM is active when accessing an even
address in word accesses or when memory is configured for a 32-bit bus to disable
the write of the high word.
SDA10
O/T
(pu_0)
nc
SDRAM Address Bit 10. Separate A10 signals enable SDRAM refresh operation while
the DSP executes non-SDRAM transactions.
SDCKE
I/O/T
(pu_m/
pd_m)
nc
SDRAM Clock Enable. Activates the SDRAM clock for SDRAM self-refresh or suspend
modes. A slave DSP in a multiprocessor system does not have the pull-up or pull-
down. A master DSP (or ID = 0 in a single processor system) has a pull-up before
granting the bus to the host, except when the SDRAM is put in self refresh mode. In
self refresh mode, the master has a pull-down before granting the bus to the host.
SDWE
I/O/T
(pu_0)
nc
SDRAM Write Enable. When sampled low while CAS is active, SDWE indicates an
SDRAM write access. When sampled high while CAS is active, SDWE indicates an
SDRAM read access. In other SDRAM accesses, SDWE defines the type of operation to
execute according to SDRAM specification.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-TS101SAB2-100 | IC DSP CONTROLLER 6MBIT 484 BGA |
| VE-B34-CY-S | CONVERTER MOD DC/DC 48V 50W |
| ATFC-0402-1N0-BT | INDUCTOR THIN FILM 1.0NH 0402 |
| ADSP-TS201SABPZ050 | IC PROCESSOR 500MHZ 576BGA |
| TAJY475M050RNJ | CAP TANT 4.7UF 50V 20% 2917 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS201SABP-060 | 功能描述:IC PROCESSOR 600MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS201SABP-10X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-15X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-ENG | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-ENG1 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。