參數資料
型號： ADUC7128BSTZ126
廠商： Analog Devices Inc
文件頁數： 65/92頁
文件大小： 0K
描述： IC DAS MCU ARM7 ADC/DDS 64-LQFP
產品培訓模塊： Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 41.78MHz
連通性： I²C，SPI，UART/USART
外圍設備： PLA，POR，PWM，PSM，溫度傳感器，WDT
輸入/輸出數： 28
程序存儲器容量： 126KB（63K x 16）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 10x12b; D/A 1x10b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 64-LQFP
包裝： 托盤
配用： EVAL-ADUC7128QSPZ-ND - KIT DEV FOR ADUC7128
ADuC7128/ADuC7129
Rev. 0 | Page 68 of 92
Bit
Description
7
Master Serial Clock Enable Bit.
Set by user to enable generation of the serial clock in master mode.
Cleared by user to disable serial clock in master mode.
6
Loop-Back Enable Bit.
Set by user to internally connect the transition to the reception to test user software.
Cleared by user to operate in normal mode.
5
Start Back-Off Disable Bit.
Set by user in multimaster mode. If losing arbitration, the master immediately tries to retransmit.
Cleared by user to enable start back-off. After losing arbitration, the master waits before trying to retransmit.
4
Hardware General Call Enable. When this bit and Bit 3 are set, and have received a general call (Address 0x00) and a data byte, the
device checks the contents of the I2C0ALT against the receive register. If the contents match, the device has received a hardware
general call. This is used if a device needs urgent attention from a master device without knowing which master it needs to turn to.
This is a “to whom it may concern” call. The ADuC7128/ADuC7129 watch for these addresses. The device that requires attention
embeds its own address into the message. All masters listen and the one that can handle the device contacts its slave and acts
appropriately. The LSB of the I2C0ALT register should always be written to a 1, as per the I2C January 2000 specification.
3
General Call Enable Bit.
Set this bit to enable the slave device to acknowledge an I2C general call, Address 0x00 (write). The device then recognizes a data
bit. If it receives a 0x06 (reset and write programmable part of slave address by hardware) as the data byte, the I2C interface resets as per
the I2C January 2000 specification. This command can be used to reset an entire I2C system. The general call interrupt status bit
sets on any general call. The user must take corrective action by setting up the I2C interface after a reset. If it receives a 0x04
(write programmable part of slave address by hardware) as the data byte, the general call interrupt status bit sets on any general
call. The user must take corrective action by reprogramming the device address.
2
Reserved.
1
Master Enable Bit.
Set by user to enable the master I2C channel.
Cleared by user to disable the master I2C channel.
0
Slave Enable Bit.
Set by user to enable the slave I2C channel. A slave transfer sequence is monitored for the device address in I2C0ID0, I2C0ID1,
I2C0ID2, and I2C0ID3. If the device address is recognized, the part participates in the slave transfer sequence.
Cleared by user to disable the slave I2C channel.
I2CxDIV Register
Name
Address
Default Value
Access
I2C0DIV
0xFFFF0830
0x1F1F
R/W
I2C1DIV
0xFFFF0930
0x1F1F
R/W
I2CxDIV are the clock divider registers.
I2CxIDx Register
Name
Address
Default Value
Access
I2C0ID0
0xFFFF0838
0x00
R/W
I2C0ID1
0xFFFF083C
0x00
R/W
I2C0ID2
0xFFFF0840
0x00
R/W
I2C0ID3
0xFFFF0844
0x00
R/W
I2C1ID0
0xFFFF0938
0x00
R/W
I2C1ID1
0xFFFF093C
0x00
R/W
I2C1ID2
0xFFFF0940
0x00
R/W
I2C1ID3
0xFFFF0944
0x00
R/W
I2CxID0, I2CxID1, I2CxID2, and I2CxID3 are slave address
device ID registers of I2Cx.
I2CxSSC Register
Name
Address
Default Value
Access
I2C0SSC
0xFFFF0848
0x01
R/W
I2C1SSC
0xFFFF0948
0x01
R/W
I2CxSSC is an 8-bit start/stop generation counter. It holds off
SDA low for start and stop conditions.
相關PDF資料
PDF描述
D38999/24MB99PN CONN RCPT 7POS JAM NUT W/PINS
ADUC7128BCPZ126 IC DAS MCU ARM7 ADC/DDS 64-LFCSP
GTC02R-22-19P CONN RCPT 14POS BOX MNT W/PINS
D38999/26FJ61PN CONN PLUG 61POS STRAIGHT W/PINS
ADUC843BCPZ62-3 IC MCU FLASH 12BIT ADC 56LFCSP
相關代理商/技術參數
參數描述
ADUC7128BSTZ1262 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
ADUC7128BSTZ126-RL 功能描述:IC DAS MCU ARM7 ADC/DDS 64-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7128BSTZ126-RL2 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
ADUC7129 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
ADUC7129BSTZ126 功能描述:IC DAS MCU ARM7 ADC/DDS 80-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*