- 您現在的位置：買賣IC網 > PDF目錄294981 > AGL10005-FFG144I FPGA, 1000000 GATES, 250 MHz, PBGA144 PDF資料下載
參數資料
| 型號： | AGL10005-FFG144I |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| 封裝： | 13 X 13 MM, 1 MM PITCH, FBGA-144 |
| 文件頁數： | 175/204頁 |
| 文件大?。?/td> | 2800K |
| 代理商： | AGL10005-FFG144I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁當前第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁
IGLOO Low-Power Flash FPGAs with Flash*Freeze Technology
2- 58
Advanced v0.1
Pin Descriptions
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O
logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O
banks.
Within
the
package,
the
GNDQ
plane
is
decoupled from the simultaneous switching noise
originated from the output buffer ground domain. This
minimizes the noise transfer within the package and
improves input signal integrity. GNDQ must always be
connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for
IGLOO V5 devices and 1.2 V or 1.5 V for IGLOO V2
devices. VCC is required for powering the JTAG state
machine in addition to VJTAG. Even when an IGLOO
device
is
in
bypass
mode
in
a
JTAG
chain
of
interconnected devices, both VCC and VJTAG must remain
powered to allow JTAG signals to pass through the
IGLOO device.
For IGLOO V2 devices, VCC can be switched dynamically
from 1.2 V to 1.5 V or vice versa. This allows in system
programming when VCC is at 1.5 V and the benefit of
low-power operation when VCC is at 1.2 V.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O
logic. Bx is the I/O bank number. There are eight I/O
banks on IGLOO devices plus a dedicated VJTAG bank.
Each bank can have a separate VCCI connection. All I/Os
in a bank will run off the same VCCIBx supply. VCCI can be
1.5 V, 1.8 V, 2.5 V, or 3.3 V, nominal voltage. Unused I/O
banks should have their corresponding VCCI pins tied to
GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O
bank. x is the bank number. Within the package, the
VMV
plane
is
decoupled
from
the
simultaneous
switching noise originated from the output buffer VCCI
domain. This minimizes the noise transfer within the
package and improves input signal integrity. Each bank
must have at least one VMV connection, and no VMV
should be left unconnected. All I/Os in a bank run off the
same VMVx supply. VMV is used to provide a quiet supply
voltage to the input buffers of each I/O bank. VMVx can
be 1.5 V, 1.8 V, 2.5 V, or 3.3 V, nominal voltage. Unused I/O
banks should have their corresponding VMV pins tied to
GND. VMV and VCCI should be at the same voltage within
a given I/O bank. Used VMV pins must be connected to
the corresponding VCCI pins of the same bank (i.e., VMV0
to VCCIB0, VMV1 to VCCIB1, etc.).
VCCPLF
PLL Supply Voltage7
Supply voltage to analog PLL, nominally 1.5 V for IGLOO
V5 devices and 1.2 V or 1.5 V for IGLOO V2 devices. If
unused, VCCPLF should be tied to either the power supply
or GND.
VCOMPLF
PLL Ground7
Ground to analog PLL power supplies. Unused VCOMPLF
pins should be connected to GND.
VJTAG
JTAG Supply Voltage
IGLOO devices have a separate bank for the dedicated
JTAG pins. The JTAG pins can be run at any voltage from
1.5 V to 3.3 V (nominal). Isolating the JTAG power supply
in a separate I/O bank gives greater flexibility in supply
selection and simplifies power supply and PCB design. If
the JTAG interface is neither used nor planned for use,
the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be
powered for JTAG operation; VJTAG alone is insufficient. If
an IGLOO device is in a JTAG chain of interconnected
boards, the board containing the IGLOO device can be
powered down, provided both VJTAG and VCC to the
IGLOO part remain powered; otherwise, JTAG signals will
not be able to transition the IGLOO device, even in
bypass mode.
Actel recommends that VPUMP and VJTAG power supplies
are kept separate with independent filtering capacitors
rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
IGLOO devices support single-voltage ISP programming
of
the
configuration
flash
and
FlashROM.
For
programming, VPUMP should be 3.3 V nominal. During
normal device operation, VPUMP can be left floating or
can be tied (pulled up) to any voltage between 0 V and
3.45 V. Programming power supply voltage (VPUMP)
range is 3.15 V to 3.45 V.
When the VPUMP pin is tied to ground, it will shut off the
charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 F and 0.33 F capacitors
(both rated at 16 V) are to be connected in parallel
across VPUMP and GND, and positioned as close to the
FPGA pins as possible.
7. The AGL030 device does not support this feature.
相關PDF資料 |
PDF描述 |
|---|---|
| AGL10005-FFG144 | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FFG256I | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FFG256 | FPGA, 1000000 GATES, 250 MHz, PBGA144 |
| AGL10005-FFG484I | FPGA, 1000000 GATES, 250 MHz, PBGA484 |
| AGL10005-FFG484 | FPGA, 1000000 GATES, 250 MHz, PBGA484 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AGL1000V2-CS144 | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144ES | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144I | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS144PP | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:IGLOO Low-Power Flash FPGAs with Flash Freeze Technology |
| AGL1000V2-CS281 | 功能描述:IC FPGA 1KB FLASH 1M 281-CSP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:IGLOO 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27） |
發布緊急采購，3分鐘左右您將得到回復。