參數資料
型號： AM29BDS320GTC8VMF
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 1.8V PROM, 90 ns, PBGA64
封裝： 8 X 9 MM, 0.80 MM PITCH, FBGA-64
文件頁數： 26/75頁
文件大?。?/td> 1075K
代理商： AM29BDS320GTC8VMF
30
Am29BDS320G
27243B2 May 15, 2007
Data
Sheet
Reset Command
Writing the reset command resets the banks to the read or erase-suspend-read
mode. Address bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the bank to which the sys-
tem was writing to the read mode. Once erasure begins, however, the device
ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins (prior to the third cycle). This re-
sets the bank to which the system was writing to the read mode. If the program
command sequence is written to a bank that is in the Erase Suspend mode, writ-
ing the reset command returns that bank to the erase-suspend-read mode. Once
programming begins, however, the device ignores reset commands until the op-
eration is complete.
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command must be
written to return to the read mode. If a bank entered the autoselect mode while
in the Erase Suspend mode, writing the reset command returns that bank to the
erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command
returns the banks to the read mode (or erase-suspend-read mode if that bank
was in Erase Suspend).
The reset command is used to exit the sector lock/unlock sequence. This com-
mand is required before reading from the bank selected for sector lock/unlock
operations.
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
quirements. The autoselect command sequence may be written to an address
within a bank that is either in the read or erase-suspend-read mode. The autose-
lect command may not be written while the device is actively programming or
erasing in the other bank.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the bank address and the au-
toselect command. The bank then enters the autoselect mode. No subsequent
data will be made available if the autoselect data is read in synchronous mode.
The system may read at any address within the same bank any number of times
without initiating another autoselect command sequence. The following table de-
scribes the address requirements for the various autoselect functions, and the
resulting data. BA represents the bank address, and SA represents the sector ad-
dress. The device ID is read in three cycles.
相關PDF資料
PDF描述
AM29DL163CB70RZCB 2M X 8 FLASH 3V PROM, 70 ns, PDSO48
AM29DL162CB120WCEB 2M X 8 FLASH 3V PROM, 120 ns, PBGA48
AM29DL162CB120EIN 2M X 8 FLASH 3V PROM, 120 ns, PDSO48
AM29DL162CT120EIB 2M X 8 FLASH 3V PROM, 120 ns, PDSO48
AM29DL320GB120PCI 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory
相關代理商/技術參數
參數描述
AM29BDS643GT5KVAI 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays
AM29BL802CB-65RZET 制造商:Spansion 功能描述:
AM29C01WW WAF 制造商:Advanced Micro Devices 功能描述:
AM29C10API 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM29C10AWW DIE 制造商:Advanced Micro Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*