參數資料
型號： AM29BDS320GTC8VMF
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 1.8V PROM, 90 ns, PBGA64
封裝： 8 X 9 MM, 0.80 MM PITCH, FBGA-64
文件頁數： 30/75頁
文件大?。?/td> 1075K
代理商： AM29BDS320GTC8VMF
34
Am29BDS320G
27243B2 May 15, 2007
Data
Sheet
DQ7 or DQ6/DQ2 in the erasing bank. Refer to the “Write Operation Status” sec-
tion on page 37 section for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is
valid. All other commands are ignored. However, note that a hardware reset im-
mediately terminates the erase operation. If that occurs, the sector erase
command sequence should be reinitiated once that bank has returned to reading
array data, to ensure data integrity.
The host system may also initiate the sector erase command sequence while the
device is in the unlock bypass mode. The command sequence is four cycles cycles
in length instead of six cycles.
Figure 2 illustrates the algorithm for the erase operation. Refer to the Erase/Pro-
gram Operations table in the AC Characteristics section for parameters and timing
diagrams.
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase
operation and then read data from, or program data to, any sector not selected
for erasure. The bank address is required when writing this command. This com-
mand is valid only during the sector erase operation, including the minimum 50
s time-out period during the sector erase command sequence. The Erase Sus-
pend command is ignored if written during the chip erase operation or Embedded
Program algorithm.
When the Erase Suspend command is written during the sector erase operation,
the device requires a maximum of 35 s to suspend the erase operation. How-
ever, when the Erase Suspend command is written during the sector erase time-
out, the device immediately terminates the time-out period and suspends the
erase operation.
After the erase operation has been suspended, the bank enters the erase-sus-
pend-read mode. The system can read data from or program data to any sector
not selected for erasure. (The device “erase suspends” all sectors selected for
erasure.) Reading at any address within erase-suspended sectors produces sta-
tus information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2
together, to determine if a sector is actively erasing or is erase-suspended. Refer
to the Write Operation Status section for information on these status bits.
After an erase-suspended program operation is complete, the bank returns to the
erase-suspend-read mode. The system can determine the status of the program
operation using the DQ7 or DQ6 status bits, just as in the standard program op-
eration. Refer to the “Write Operation Status” section for more information.
In the erase-suspend-read mode, the system can also issue the autoselect com-
mand sequence. Refer to the “Autoselect Functions” section on page 16 and
To resume the sector erase operation, the system must write the Erase Resume
command. The bank address of the erase-suspended bank is required when writ-
ing this command. Further writes of the Resume command are ignored. Another
Erase Suspend command can be written after the chip has resumed erasing.
相關PDF資料
PDF描述
AM29DL163CB70RZCB 2M X 8 FLASH 3V PROM, 70 ns, PDSO48
AM29DL162CB120WCEB 2M X 8 FLASH 3V PROM, 120 ns, PBGA48
AM29DL162CB120EIN 2M X 8 FLASH 3V PROM, 120 ns, PDSO48
AM29DL162CT120EIB 2M X 8 FLASH 3V PROM, 120 ns, PDSO48
AM29DL320GB120PCI 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory
相關代理商/技術參數
參數描述
AM29BDS643GT5KVAI 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays
AM29BL802CB-65RZET 制造商:Spansion 功能描述:
AM29C01WW WAF 制造商:Advanced Micro Devices 功能描述:
AM29C10API 制造商:Rochester Electronics LLC 功能描述:- Bulk
AM29C10AWW DIE 制造商:Advanced Micro Devices 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*