- 您現在的位置：買賣IC網 > PDF目錄223346 > AM29BDS320GTC8VMF (SPANSION LLC) 2M X 16 FLASH 1.8V PROM, 90 ns, PBGA64 PDF資料下載
參數資料
| 型號： | AM29BDS320GTC8VMF |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 1.8V PROM, 90 ns, PBGA64 |
| 封裝： | 8 X 9 MM, 0.80 MM PITCH, FBGA-64 |
| 文件頁數： | 29/75頁 |
| 文件大?。?/td> | 1075K |
| 代理商： | AM29BDS320GTC8VMF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
May 15, 2007 27243B2
Am29BDS320G
33
Data
Sheet
the system to preprogram prior to erase. The Embedded Erase algorithm auto-
matically preprograms and verifies the entire memory for an all zero data pattern
prior to electrical erase. The system is not required to provide any controls or tim-
ings during these operations. Table 14, “Command Definitions,” on page 36
shows the address and data requirements for the chip erase command sequence.
When the Embedded Erase algorithm is complete, that bank returns to the read
mode and addresses are no longer latched. The system can determine the status
of the erase operation by using DQ7 or DQ6/DQ2. Refer to the “Write Operation
Status” section for information on these status bits.
Any commands written during the chip erase operation are ignored. However,
note that a hardware reset immediately terminates the erase operation. If that
occurs, the chip erase command sequence should be reinitiated once that bank
has returned to reading array data, to ensure data integrity.
The host system may also initiate the chip erase command sequence while the
device is in the unlock bypass mode. The command sequence is two cycles in
length instead of six cycles. See Table 14 for details on the unlock bypass com-
mand sequences.
Figure 2 illustrates the algorithm for the erase operation. Refer to the Erase/Pro-
gram Operations table in the AC Characteristics section for parameters and timing
diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is
initiated by writing two unlock cycles, followed by a set-up command. Two addi-
tional unlock cycles are written, and are then followed by the address of the
sector to be erased, and the sector erase command. Table 14 shows the address
and data requirements for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Em-
bedded Erase algorithm automatically programs and verifies the entire memory
for an all zero data pattern prior to electrical erase. The system is not required to
provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of no less than
35 s occurs. During the time-out period, additional sector addresses and sector
erase commands may be written. Loading the sector erase buffer may be done
in any sequence, and the number of sectors may be from one sector to all sectors.
The time between these additional cycles must be less than 50 s, otherwise era-
sure may begin. Any sector erase address and command following the exceeded
time-out may or may not be accepted. It is recommended that processor inter-
rupts be disabled during this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase command is written. Any
command other than Sector Erase or Erase Suspend during the time-out period
resets that bank to the read mode. The system must rewrite the command se-
quence and any additional addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out
(See “DQ3: Sector Erase Timer” section on page 42.). The time-out begins from
the rising edge of the final WE# pulse in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading
array data and addresses are no longer latched. Note that while the Embedded
Erase operation is in progress, the system can read data from the non-erasing
bank. The system can determine the status of the erase operation by reading
相關PDF資料 |
PDF描述 |
|---|---|
| AM29DL163CB70RZCB | 2M X 8 FLASH 3V PROM, 70 ns, PDSO48 |
| AM29DL162CB120WCEB | 2M X 8 FLASH 3V PROM, 120 ns, PBGA48 |
| AM29DL162CB120EIN | 2M X 8 FLASH 3V PROM, 120 ns, PDSO48 |
| AM29DL162CT120EIB | 2M X 8 FLASH 3V PROM, 120 ns, PDSO48 |
| AM29DL320GB120PCI | 32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM29BDS643GT5KVAI | 制造商:Spansion 功能描述:FLASH PARALLEL 1.8V 64MBIT 4MX16 55NS 44FBGA - Trays |
| AM29BL802CB-65RZET | 制造商:Spansion 功能描述: |
| AM29C01WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| AM29C10API | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AM29C10AWW DIE | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。