- 您現在的位置：買賣IC網 > PDF目錄362278 > AM486DX Am486DX - Am486DX Block Diagram PDF資料下載
參數資料
| 型號： | AM486DX |
| 英文描述： | Am486DX - Am486DX Block Diagram |
| 中文描述： | Am486DX - Am486DX框圖 |
| 文件頁數： | 16/52頁 |
| 文件大?。?/td> | 1242K |
| 代理商： | AM486DX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
16
Am486DE2 Microprocessor
SMIACT (New)
SMM Interrupt Active (Active-Low Output)
SMIACT goes Low in response to SMI. It indicates that
the processor is operating under SMM control. SMIACT
remains Low until the processor receives a RESET sig-
nal or executes the Resume instruction (RSM) to leave
SMM. This signal is always driven. It does not float dur-
ing bus HOLD or BOFF.
Note:
Do not use SRESET to exit from SMM. The sys-
tem should block SRESET during SMM.
SRESET (New)
Soft Reset (Input)
The CPU samples SRESET on every rising clock edge.
If SRESET is sampled active, the SRESET sequence
begins on the next instruction boundary. SRESET
resets the processor, but, unlike RESET, does not
cause it to sample UP or WB/WT, or affect the FPU,
cache, CD and NW bits in CR0, and SMBASE. SRESET
is asynchronous and must meet the same timing as
RESET.
STPCLK (New)
Stop Clock (Active-Low Input)
A Low input signal indicates a request has been made
to turn off the CLK input. When the CPU recognizes a
STPCLK, the processor:
I
stops execution on the next instruction boundary
(unless superseded by a higher priority interrupt)
I
empties all internal pipelines and write buffers
I
generates a Stop Grant acknowledge bus cycle
STPCLK is active Low and has an internal pull-up resis-
tor. STPCLK is asynchronous, but it must meet setup
and hold times t
20
and t
21
to ensure recognition in any
specific clock. STPCLK must remain active until the
Stop Clock special bus cycle is issued and the system
returns either RDY or BRDY.
TCK
Test Clock (Input)
Test Clock provides the clocking function for the JTAG
boundary scan feature. TCK clocks state information
and data into the component on the rising edge of TCK
on TMS and TDI, respectively. Data is clocked out of the
component on the falling edge of TCK on TDO.
TDI
Test Data Input (Input)
TDI is the serial input that shifts JTAG instructions and
data into the tested component. TDI is sampled on the
rising edge of TCK during the SHIFT-IR and the SHIFT-
DR TAP (Test Access Port) controller states. During all
other TAP controller states, TDI is ignored. TDI uses an
internal weak pull-up.
TDO
Test Data Output (Output)
TDO is the serial output that shifts JTAG instructions
and data out of the component. TDO is driven on the
falling edge of TCK during the SHIFT-IR and SHIFT-DR
TAP controller states. Otherwise, TDO is three-stated.
TMS
Test Mode Select (Input)
TMS is decoded by the JTAG TAP to select the opera-
tion of the test logic. TMS is sampled on the rising edge
of TCK. To guarantee deterministic behavior of the TAP
controller, the TMS pin has an internal pull-up resistor.
UP
Upgrade Present (Input)
The processor samples the Upgrade Present (UP) pin
in the clock before the falling edge of RESET. If it is Low,
the processor three-states its outputs immediately. UP
must remain asserted to keep the processor inactive.
The pin uses an internal pull-up resistor.
VOLDET (New, 168-Pin PGA Package only)
Voltage Detect (Output)
VOLDET provides an external signal to allow the system
to determine the CPU input power level (3 V or 5 V). For
the Am486DE2, the pin ties internally to V
SS
.
WB/WT (New)
Write-Back/Write-Through (Input)
WB/WT is sampled Low at RESET, and all cache-line
fills are write-through. WB/WT has an internal weak pull-
down. This pin should be tied Low for the Am486DE2
microprocessor.
W/R
Write/Read (Output)
A High output indicates a write cycle. A Low output in-
dicates a read cycle.
Note:
The Am486DE2 microprocessor does not use the
V
CC5
pin used by some 3-V, clock-tripled, 486-based
processors. The corresponding pin on the Am486DE2
microprocessor is an Internal No Connect (INC).
相關PDF資料 |
PDF描述 |
|---|---|
| AM486DXPGA | Am486DX PGA - Am486DX PGA Package Temperature Comparisons |
| AM486DXSQFP | 70NS, PLCC, IND TEMP(EEPROM) |
| AM486 | Am486 Microprocessor Software User＇s Manual? 4.40MB (PDF) |
| AM49DL3208G | Am49DL3208G - Stacked Multi-Chip Package (MCP) Flash Memory and pSRAM |
| AM49DL320BG | Am49DL320BG - Stacked Multi-Chip Package (MCP) Flash Memory and SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM486DX/DX2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Am486DX/DX2 Hardware Reference Manual |
| AM486DX2 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Am5X86⑩ Microprocessor Family |
| AM486DX2-66V16BGC | 制造商:Advanced Micro Devices 功能描述:MPU AM486 RISC 32-Bit 0.35um 66MHz 5V 168-Pin PGA |
| AM486DX2-66V16BGI | 制造商:Advanced Micro Devices 功能描述:MPU AM486 RISC 32-Bit 0.35um 66MHz 5V 168-Pin PGA |
| AM486DX2-66V16BHI | 制造商:Advanced Micro Devices 功能描述:MPU AM486 RISC 32-Bit 0.35um 66MHz 5V 208-Pin SQFP |
發布緊急采購，3分鐘左右您將得到回復。