參數資料
型號: AM79C972BVIW
廠商: ADVANCED MICRO DEVICES INC
元件分類: 微控制器/微處理器
英文描述: PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support
中文描述: 5 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP176
封裝: TQFP-176
文件頁數: 31/130頁
文件大?。?/td> 1580K
代理商: AM79C972BVIW
Am79C972
31
During the boot procedure, the system will try to find an
Expansion ROM. A PCI system assumes that an Ex-
pansion ROM is present when it reads the ROM signa-
ture 55H (byte 0) and AAH (byte 1).
Slave Cycle Termination
There are three scenarios besides normal completion
of a transaction where the Am79C972 controller is the
target of a slave cycle and it will terminate the access.
Disconnect When Busy
The Am79C972 controller cannot service any slave ac-
cess while it is reading the contents of the EEPROM.
Simultaneous access is not allowed in order to avoid
conflicts, since the EEPROM is used to initialize some
of the PCI configuration space locations and most of
the BCRs and CSR116. The EEPROM read operation
will always happen automatically after the deassertion
of the RST pin. In addition, the host can start the read
operation by setting the PREAD bit (BCR19, bit 14).
While the EEPROM read is on-going, the Am79C972
controller will disconnect any slave access where it is
the target by asserting STOP together with DEVSEL,
while driving TRDY high. STOP will stay asserted until
the end of the cycle.
Note that I/O and memory slave accesses will only be
disconnected if they are enabled by setting the IOEN or
MEMEN bit in the PCI Command register. Without the
enable bit set, the cycles will not be claimed at all.
Since H_RESET clears the IOEN and MEMEN bits for
the automatic EEPROM read after H_RESET, the dis-
connect only applies to configuration cycles.
A second situation where the Am79C972 controller will
generate a PCI disconnect/retry cycle is when the host
tries to access any of the I/O resources right after hav-
ing read the Reset register. Since the access gener-
ates an internal reset pulse of about 1
μ
s in length, all
further slave accesses will be deferred until the internal
reset operation is completed. See Figure 6.
Disconnect Of Burst Transfer
The Am79C972 controller does not support burst ac-
cess to the configuration space, the I/O resources, or to
the Expansion Bus. The host indicates a burst transac-
tion by keeping FRAME asserted during the data
phase. When the Am79C972 controller sees FRAME
and IRDY asserted in the clock cycle before it wants to
assert TRDY, it also asserts STOP at the same time.
The transfer of the first data phase is still successful,
since IRDY and TRDY are both asserted. See Figure 7.
.
Figure 6.
Disconnect Of Slave Cycle When Busy
Figure 7.
Disconnect Of Slave Burst Transfer - No
Host Wait States
FRAME
CLK
AD
IRDY
TRDY
C/BE
DEVSEL
STOP
1
2
3
4
5
CMD
PAR
PAR
PAR
BE
DATA
ADDR
21485C-9
FRAME
CLK
AD
IRDY
TRDY
C/BE
DEVSEL
STOP
1
2
3
4
5
BE
PAR
PAR
PAR
BE
DATA
1st DATA
21485C-10
相關PDF資料
PDF描述
AM79C974 PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems
AM79C974KCW PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems
AM79C975 PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY
AM79C973 PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY
AM79C973KCW PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY
相關代理商/技術參數
參數描述
AM79C973 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY
AM79C973/75 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Board Layout Considerations for the Am79C973/75 Network Interface? - (PDF)
AM79C973/AM79C975 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Am79C973/Am79C975 - PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY
AM79C973AVC\\W 制造商:Advanced Micro Devices 功能描述:
AM79C973AVC\W 制造商:Advanced Micro Devices 功能描述: