- 您現在的位置：買賣IC網 > PDF目錄362330 > AN-14 TOPSwitch Tips. Techniques & Troubleshooting Guide PDF資料下載
參數資料
| 型號： | AN-14 |
| 英文描述： | TOPSwitch Tips. Techniques & Troubleshooting Guide |
| 中文描述： | TOPSwitch的提示。技術 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 246K |
| 代理商： | AN-14 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AN-14
6
B
6/96
POWER FACTOR CORRECTION CIRCUITS
CAUSE
SYMPTOM
WHAT TO DO
Drain voltage rings below Source
potential
Precompensation resistor value is
not correct
Precompensation current
waveform is being filtered
Output voltage ripple modulates
duty cycle
Inductor value is too large and
enters continuous mode at peak of
rectified AC input voltage
Inductor value is too small and
TOPSwitch
current limit reduces
duty cycle
Precompensation resistor current
disables auto-restart
PFC stage does not start
Total Harmonic Distortion
(THD) is greater than 10%
PFC stage turns off with short
interruption in AC power
Add fast recovery blocking diode in series with Drain
(Section 19.1)
Adjust precompensation resistor until optimum THD
has been obtained (See DN-7)
Reduce bypass capacitance on Control pin to less than
4.7
μ
F
Add resistor (75 to 200
) between Control pin bypass
capacitor and auto-restart/compensation capacitor (R2
in Figure 19)
Increase auto-restart/compensation capacitor to reject
output voltage ripple
Decrease inductor value (See DN-7)
Increase inductor value (See DN-7)
Use
TOPSwitch
with higher current limit
Add 2.7 k
to 6.8 k
resistor across C3 (Figure 19) to
shunt precompensation current from control pin
(See DN-7)
相關PDF資料 |
PDF描述 |
|---|---|
| AN-21 | TOPSwitch-II Flyback Quick Selection Curves |
| AN-26 | TOPSwitch-FX Flyback Quick Selection Curves |
| AN-35 | LinkSwitch Design Guide |
| AN002M4-78 | SP4T RF Absorptive Switch |
| AN002R2-29 | SPDT RF Reflective Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN1405D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:3.3V / 5V ECL 2-Input Differential XOR/XNOR |
| AN1406 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:DESIGNING WITH PECL (ECL AT + 5.0) |
| AN1406/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:DESIGNING WITH PECL (ECL AT + 5.0) |
| AN1406D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:3.3V / 5V ECL 2-Input Differential XOR/XNOR |
| AN14-17A | 制造商:AN# - MILITARY 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。