- 您現在的位置：買賣IC網 > PDF目錄362345 > AOP-PXB4340 ATM OAM Processor PDF資料下載
參數資料
| 型號： | AOP-PXB4340 |
| 英文描述： | ATM OAM Processor |
| 中文描述： | 自動柜員機的OAM處理器 |
| 文件頁數： | 27/185頁 |
| 文件大小： | 2552K |
| 代理商： | AOP-PXB4340 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁
3;%(
Data Sheet
2-27
04.2000
)XQFWLRQDO'HVFULSWLRQ
2$0)XQFWLRQV2YHUYLHZ
There are two groups of applications for OAM functions: alarms and measurements. Alarm
functions inform users and network operators about network failures. These include the OAM
functions
Alarm Indication Signal (AIS)
Remote Defect Indication (RDI)
Continuity Check (CC).
AIS and RDI are used to convey transmission line failure information to subscriber and network
operator; CC detects ATM layer failures.
As failure events are unpredictable the alarm supervising HW is always running. When a failure
occurs the notification process starts automatically.
Measurements are initiated for diagnosis purposes by the network operator. Therefore these
functions do not need to be active permanently for all connections. The respective OAM
functions are:
Loopback LB
Performance Monitoring PM
LB checks the connectivity of a connection by sending a single cell which is looped back at
predefined points. LB is used e.g. immediately after connection set-up or periodically to check
all permanent connections of a network using end-to-end or segment LB. A network operator
could also use intra-domain LB to localize a failed link. Another option for loopback are
subscriber initiated loops either end-to-end to the partner or access line LB to the first node in
the network.
PM is a more precise tool than LB. It checks not only the connectivity, but the real performance
of a connection in terms of bit failures and cell losses. As it requires complex HW support and
SW performance PM will not be activated permanently for all connections. E.g. VPCs or
permanent VCCs could be monitored if a subscriber pays for this service. Also a network
operator would use PM to check the quality of a connection if a subscriber complains about it.
$ODUP2$0)XQFWLRQV$,65',&&
There are two types of failures detected by the alarm functions: transmission line failures and
ATM layer failures. Transmission line failures are e.g. line brakes, failures of lasers or failures of
reception diodes. Typical ATM layer failures are the misrouting of cells in the switching fabric or
a falsified entry in a routing table. In this case all cells of a connection are forwarded to a wrong
destination.
7UDQVPLVVLRQ/LQH)DLOXUHV$,65',
Transmission line failures are recognized by the receiving PHY and conveyed to the PXB 4340
AOP by the on-board control processor. It is sufficient to set one single bit for the respective PHY
to initiate the periodic insertion of AIS cells for all affected connections. In the external RAM entry
a bit CARIEN exists for F5-AIS and a bit PARIEN for F4-AIS ( for CARIEN see
VHFWLRQ
page 100, for upstream and
VHFWLRQ
VHFWLRQ
page 107, for upstream and
VHFWLRQ
these bits are set to ’1’, the insertion of AIS cells is enabled. Note, that no F4 OAM/User-Flow is
supported if the LCI-Mode "10" in register UTCONF1 is selected (see
VHFWLRQ
Further the bit DISF4 and DISF5 in the external RAM entries have to be set to ’0’ to enable the
page 112, for downstream; for PARIEN see
page 118, for downstream). When
page 88).
相關PDF資料 |
PDF描述 |
|---|---|
| AOP3510F1 | Voltage-Feedback Operational Amplifier |
| AOP3510J3 | Voltage-Feedback Operational Amplifier |
| AOP8 | ISA BUS KARTE 8KANAL D/A WANDLER 12BIT |
| AP-30711P2-301 | Converter |
| AP-30711P2-301V | Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AOQW-100 | 制造商:IDEC CORPORATION 功能描述:TW SQ FLUSH OPER PB |
| AOQW101-B | 制造商:IDEC CORPORATION 功能描述:TW SQ FLUSH PB |
| AOQW101FN-W/O | 制造商:IDEC CORPORATION 功能描述:COLOR BUTTON |
| AOQW101-G | 制造商:IDEC CORPORATION 功能描述:TW SQ FLUSH PB |
| AOQW101-R | 制造商:IDEC CORPORATION 功能描述:TW SQ FLUSH PB |
發布緊急采購，3分鐘左右您將得到回復。