參數資料
型號： AS8510-ASST-500
廠商： ams
文件頁數： 13/47頁
文件大?。?/td> 0K
描述： IC BATTERY MANAGEMENT 20-SSOP
產品培訓模塊： AS8510 Data Acquisition IC
標準包裝： 1
類型： 電池管理
輸入類型： 模擬，數字
輸出類型： 模擬，數字
接口： SPI 串行
電流 - 電源： 5.5mA
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 標準包裝
其它名稱： AS8510-ASST-500DKR
Revision 3.5
19 - 46
AS8510
Datasheet - Detailed Descr i p ti on
7.4.1 Normal Mode 1 (NOM1)
On Power-on-reset of the device, AS8510 goes into STOP State.
Transition to Normal mode1 (NOM1) occurs when the “START BIT” D0 of Mode Control Register MOD_CTL_REG in Table 33 is set to “1”
through the serial port SPI. Data Rate of voltage and current channels can be independently programmed and both the channels generate
interrupts for every output available from ADC. The interrupt signal is generated on the INT pin. The width of the interrupt pulse is eight cycles of
lp_clk. The data is stable up to the next interrupt. If the data rate is different for the two channels, the interrupt rate would follow the higher rate
among the two channels. Data update can be known by reading the status register. The functionality is explained in the waveform shown in
Figure 5. When the device is configured to NORMAL Mode1 from any mode the configuration should be through the STOP state only.
Figure 5. Normal Mode 1
7.4.2 Normal Mode 2 (NOM2)
NOM2 differs from NOM1 in such a way that it allows for a relaxed data rate at a period of TMC by programming the corresponding register as
long as the amplitude of current is less than a programmed threshold ITHC. However, when, the measured input signal exceeds the programmed
threshold, the data rate is changed to the rate of NOM1 mode.
Transition to NOM2 occurs when the “START BIT” D0 of Mode Control register MOD_CTL_REG in Table 33 is set to 1 and mode control bits to
01 through SPI. In this mode the data rate should be programmed with the time of TMC. An interrupt signal is generated on INT at the rate of TMC
secs with a pulse width of eight cycles of lp_clk. The data is stable up to the next interrupt. The data sample is compared against the programmed
threshold and when it is exceeded, the data sampling rate is changed to provide data at the data rate of NOM1 mode. However, as soon as the
data sample amplitude falls below the programmed threshold, the sampling rate is restored to provide data at the rate of TMC. The functionality is
illustrated in the waveform Figure 6.
Sampling with f1
INT at f1 rate from
current channel
Current Channel
DATA Register
t
I
START
STOP
t
V,T
Sampling with f2
Voltage Channel
DATA Register
Interrupt fromthe current channel is at f1 rate which is integer multiple of f2 rate fromvoltage channel
IDATA
V,TDATA
TINT
相關PDF資料
PDF描述
VI-BTF-IX-F3 CONVERTER MOD DC/DC 72V 75W
VE-J3N-IZ-B1 CONVERTER MOD DC/DC 18.5V 25W
NCV1124DR2G IC SENSOR DUAL VAR-RELUCT 8-SOIC
MS27508E24B1PB CONN RCPT 128POS BOX MNT W/PINS
D38999/26WJ4PN CONN PLUG 56POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
AS8510-COPPER-SHUNT 功能描述:DEMO BOARD FOR AS8510 制造商:ams 系列:- 零件狀態:在售 主要用途:接口，數據捕捉 嵌入式:- 使用的 IC/零件:AS8510 主要屬性:- 輔助屬性:圖形用戶界面 所含物品:板 標準包裝:1
AS8510-DB 制造商:ams 功能描述:AS8510 Demo Board
AS8515-ZMFM 制造商:ams 功能描述:IC BATTERY MANAGEMENT 制造商:ams 功能描述:Data Acquisition System w/ Power Management and LIN Transceiver - MLF-32 制造商:ams 功能描述:T&R / MLF 32 (5x5)
AS8515-ZMFP 制造商:ams 功能描述:IC INTERFACE TRANSCEIVER 制造商:ams 功能描述:T&R / MLF 32 (5x5)
AS8520 制造商:AMSCO 制造商全稱:austriamicrosystems AG 功能描述:LIN Transceiver with Voltage Regulator, Attenuator, Relay Drivers, MCU Interface for Automotive Applications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*