- 您現在的位置：買賣IC網 > PDF目錄67389 > AT42QT1110-MZ (ATMEL CORP) PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | AT42QT1110-MZ |
| 廠商： | ATMEL CORP |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| 封裝： | 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 3/46頁 |
| 文件大?。?/td> | 657K |
| 代理商： | AT42QT1110-MZ |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
11
9570I–AT42–03/10
AT42QT1110-MZ/AT42QT1110-AZ
4.1.3
CRC Bytes
If enabled, a CRC checking procedure is implemented on all communications between the SPI
master and the QT1110. In this case, each command or report request sent by the master must
have a byte appended containing the CRC checksum of the data sent. The QT1110 will not
respond to commands until the CRC byte has been received and verified.
Sample C code showing the algorithm for calculating the CRC of the data can be found in
When the QT1110 is expecting a CRC byte, it returns (on MISO) the calculated CRC byte which
it expects to receive. This is sent simultaneously with the QT1110 receiving the CRC byte from
the master (that is, during the same byte exchange). This allows both devices to confirm that the
data was sent correctly.
All data returned by the QT1110 is also be followed by a CRC byte, allowing the master to
confirm the integrity of the data transmission.
4.1.4
SPI Commands
There are three types of communication between the SPI master and the QT1110:
Control commands (see Section 5 on page 22)
– To send control instructions to the QT1110
Report requests (see Section 6 on page 24)
– To reading status information from the QT1110
Setup commands (see Section 7 on page 28)
– To set configuration options (“Set” instructions)
– To read configuration options (“Get” instructions)
Additionally the “Null” command (0x00) is transmitted by the host device as it is receiving data
from the QT1110.
4.1.4.1
Control Commands
A control command is an instruction sent to the QT1110 that controls operations of the device,
and for which no response is required. Examples of control commands are: “Reset”, “Calibrate”,
“Send Setups”.
With the exception of “Send Setups”, control commands normally require a single byte
exchange, unless CRC checking is enabled, in which case a second byte must be transmitted
by the host with the calculated CRC of the command byte.
Figure 4-1.
Sleep Command – CRC Disabled
Host (Sends on MOSI)
Device (Responds on MISO)
Simultaneous
Transmission
Command: 0x05
Response: 0x55 ( Idle”
Fresh Command)
“
–
相關PDF資料 |
PDF描述 |
|---|---|
| AT42QT1111-AU | PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT |
| AT76C453AC-MY19T | IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT |
| ATF-33143-TR2 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-BLK | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
| ATF-33143-TR1 | X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT42QT1111-AU | 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1111-AU QS383 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
| AT42QT1111MU | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC |
| AT42QT1111-MU | 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: |
| AT42QT1111-MU QS384 | 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC |
發布緊急采購，3分鐘左右您將得到回復。