參數資料
型號： AT42QT1110-MZ
廠商： ATMEL CORP
元件分類： 速度傳感器和接近開關
英文描述： PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
封裝： 5 X 5 MM, 0.50 MM PITCH, ROHS COMPLIANT, MO-220VHHD-2, QFN-32
文件頁數： 9/46頁
文件大?。?/td> 657K
代理商： AT42QT1110-MZ
17
9570I–AT42–03/10
AT42QT1110-MZ/AT42QT1110-AZ
4.1.6.4
Quick SPI Mode timing
In Quick SPI mode, the minimum time between byte exchanges is reduced to 50 S.
If a pause in communications of 100 ms is detected during reading of the 7-byte report, the
QT1110 resets the exchange, and on the next byte read it returns byte 0 of the report.
4.2
Reset
The QT1110 can be reset using one of two methods:
Hardware reset: An external reset logic line can be used if desired, fed into the RESET pin.
However, under most conditions it is acceptable to tie RESET to Vdd.
Software reset: A software reset can be forced using the “Reset” control command.
For both methods, the device will follow the same initialization sequence. If there any saved
settings in the EEPROM, these are loaded into RAM. Otherwise the default settings are applied.
Note:
The SPI interface becomes active after the QT1110 has completed its startup sequence,
taking approximately 160 ms after power on/reset.
4.3
Sleep Mode
The QT1110 can be put into a very low power sleep mode (typically < 2 A). During sleep mode,
no keys are measured and the DETECT outputs are all put into high impedience mode to
minimize current consumption. The device remains in sleep mode until a falling edge is detected
on either the SS pin or the CHANGE pin. When the QT1110 wakes from sleep mode, it
continues to operate as it was before it was put into sleep mode. The QT1110 requires
approximately 100 s to wake from sleep mode and will not respond correctly to SPI
communications until the wake-up procedure is complete. The low level on the SS or CHANGE
pin that is used to wake the device must be maintained for 100 s to ensure correct operation.
Note:
If the device is set to sleep mode for an extended period, the host should initiate a
recalibration immediately after waking the QT1110.
4.4
Calibration
The device can be forced to recalibrate the sensor keys at any time. This can be useful where,
for example, a portable device is plugged into mains power, or during product development
when settings are being tuned.
The QT1110 can also be configured to automatically recalibrate if it remains in detection for too
long. This avoids keys becoming “stuck” after a prolonged period of uninterrupted detection. See
4.5
CHANGE Pin
The CHANGE pin can be configured using the Comms Options setup byte (see Section 7.5 on
page 30) to act in one of two modes:
Data mode
–The CHANGE pin is asserted (pulled low) when the detection status of a key
changes from that last sent to the host; that is when a key-touch or key-release event
occurs.
–The CHANGE pin is pulled low when a key’s status changes and is only released
when the “Send All keys” report is requested (0xC1), or the key status information
bytes are read in Quick SPI mode (see Section 7.5 on page 30).
相關PDF資料
PDF描述
AT42QT1111-AU PROXIMITY SENSOR-CAPACITIVE, 0-5V, SQUARE, SURFACE MOUNT
AT76C453AC-MY19T IMAGE SENSOR-CMOS, 708(H) X 494(V) PIXEL, 30fps, SURFACE MOUNT
ATF-33143-TR2 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-BLK X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
ATF-33143-TR1 X BAND, Si, N-CHANNEL, RF SMALL SIGNAL, HEMFET
相關代理商/技術參數
參數描述
AT42QT1111-AU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-AU QS383 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC
AT42QT1111MU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:QTouch? 11-key Sensor IC
AT42QT1111-MU 功能描述:電容觸摸傳感器 QTouch 11 Key Touch Sensor IC RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍:
AT42QT1111-MU QS384 制造商:Atmel Corporation 功能描述:QTOUCH 11 KEY TOUCH SENSOR IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*