參數資料
型號: AT90USB647-AU
廠商: Atmel
文件頁數: 66/106頁
文件大?。?/td> 0K
描述: IC AVR MCU 64K 64TQFP
產品培訓模塊: megaAVR Introduction
標準包裝: 450
系列: AVR®
應用: USB 微控制器
核心處理器: AVR
程序存儲器類型: 閃存(64 kB)
控制器系列: AT90 USB
RAM 容量: 4K x 8
接口: 2 線串行,SPI 串行,USART,USB
輸入/輸出數: 48
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 64-TQFP,64-VQFP
包裝: 托盤
供應商設備封裝: 64-TQFP
配用: ATSTK600-RC17-ND - STK600 ROUTING CARD AVR
ATSTK525-ND - KIT STARTER FOR AT90USB
AT90USBKEY2-ND - KIT DEMO FOR AT90USB
其它名稱: AT90USB647-16AU
AT90USB647-16AU-ND
62
7593L–AVR–09/12
AT90USB64/128
Bit 2 – BORF: Brown-out Reset Flag
This bit is set if a Brown-out Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
Bit 1 – EXTRF: External Reset Flag
This bit is set if an External Reset occurs. The bit is reset by a Power-on Reset, or by writing a
logic zero to the flag.
Bit 0 – PORF: Power-on Reset Flag
This bit is set if a Power-on Reset occurs. The bit is reset only by writing a logic zero to the flag.
To make use of the Reset Flags to identify a reset condition, the user should read and then
Reset the MCUSR as early as possible in the program. If the register is cleared before another
reset occurs, the source of the reset can be found by examining the Reset Flags.
9.7
Internal voltage reference
Atmel AT90USB64/128 features an internal bandgap reference. This reference is used for
Brown-out Detection, and it can be used as an input to the Analog Comparator or the ADC.
9.7.1
Voltage reference enable signals and start-up time
The voltage reference has a start-up time that may influence the way it should be used. The
start-up time is given in Table 9-4. To save power, the reference is not always turned on. The
reference is on during the following situations:
1.
When the BOD is enabled (by programming the BODLEVEL [2..0] Fuse).
2.
When the bandgap reference is connected to the Analog Comparator (by setting the
ACBG bit in ACSR).
3.
When the ADC is enabled.
Thus, when the BOD is not enabled, after setting the ACBG bit or enabling the ADC, the user
must always allow the reference to start up before the output from the Analog Comparator or
ADC is used. To reduce power consumption in Power-down mode, the user can avoid the three
conditions above to ensure that the reference is turned off before entering Power-down mode.
Table 9-4.
Internal voltage reference characteristics.
Symbol
Parameter
Condition
Min.
Typ.
Max.
Units
VBG
Bandgap reference voltage
1.0
1.1
1.2
V
tBG
Bandgap reference start-up time
40
70
s
IBG
Bandgap reference current
consumption
10
A
相關PDF資料
PDF描述
395-024-541-204 CARD EDGE 24POS DL .100X.200 BLK
395-024-541-202 CARD EDGE 24POS DL .100X.200 BLK
395-024-541-201 CARD EDGE 24POS DL .100X.200 BLK
395-024-540-804 CARD EDGE 24POS DL .100X.200 BLK
FT24C08A-UTG-T IC EEPROM 8KBIT 1MHZ 8TSSOP
相關代理商/技術參數
參數描述
AT90USB647-AUR 功能描述:8位微控制器 -MCU 64K Flash; 2K EEPROM 4K SRAM; 48 IO Pins RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90USB647-MU 功能描述:8位微控制器 -MCU AVR USB 64K FLSH-OTG 16MHz Ind Temp RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90USB647-MUR 功能描述:8位微控制器 -MCU USB 64K FLASH 16 MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT90USB64X 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:USB DFU Bootloader
AT90USB82 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 8/16K Bytes of ISP Flash and USB Controller